The basics
How an air source heat pump works
An air source heat pump takes heat from outside air and transfers it into the home’s heating and hot water system. Here is what each part does, in plain English, and why it behaves differently from a boiler.
The basic idea
A fridge keeps food cold by moving heat out of the inside of the cabinet and releasing it at the back. An air source heat pump uses the same principle in the other direction: it collects heat from the air outside your home and moves it into the water that circulates through your radiators and hot water cylinder.
Even on a cold day, outside air contains heat energy. The heat pump uses a refrigerant circuit, a compressor and heat exchangers to gather that heat and raise it to a useful temperature. The heat is then passed into your heating water, which flows around the house just as it would with a boiler. Electricity runs the compressor, fans and pumps; nothing is burned inside your home.
If you are new to the words used here, our heat pump glossary explains terms such as flow temperature, COP and SCOP without assuming any background knowledge.
The main parts of a system
The outdoor unit
This is the box you see outside, usually on the ground or on a wall bracket. It contains a fan that draws outside air across a heat exchanger, and the components that gather heat from that air. It needs space around it for air to move freely, and the installer will consider where it can sit, how it will be reached for maintenance and how pipework will run into the house.
The hot water cylinder
A heat pump does not heat tap water instantly in the way a combination boiler does. Instead, hot water is usually stored in a cylinder and heated over time, ready for when you need it. Homes that already have a cylinder may need a different one suited to a heat pump; homes that had a combination boiler will usually need space found for one. Your installer’s survey should explain what is proposed and why.
Controls
Controls tell the heat pump how warm the house should be and when hot water is needed. Heat pumps tend to work best when they can run steadily rather than switching on and off in short bursts, so the controls are set up with that in mind. Ask your installer to show you how they work at handover and to leave written instructions.
Your radiators and pipework
In most UK homes, the heat pump connects to the radiators and pipework that are already there. That is what “retrofit” means, and it is the normal case, which is why we have a whole page on fitting a heat pump to an existing heating system.
Why lower flow temperatures are normal
“Flow temperature” is the temperature of the water leaving the heat source and flowing to your radiators. Heat pumps are designed to run at lower flow temperatures than most gas boilers, for longer periods. Radiators may feel warm rather than hot to the touch, and the heating may be on for more of the day. This is how the system is meant to behave, not a sign that something is wrong.
Because the water is cooler, the system relies on moving enough of it, steadily, through every radiator. That is why your installer will think carefully about radiator sizes, pipe sizes and the flow of water through the whole circuit. It is also why anything that restricts that flow deserves attention before the heat pump is connected.
Air-to-water is the usual kind in UK homes
There are different kinds of heat pump. The one this site focuses on, and the kind most UK homes have fitted, heats water for radiators and taps. The government’s deployment statistics show how dominant that type is among retrofit installations:
In 2026 up to the end of Q2, 99% of retrofit heat pump installations in UK homes were air-to-water heat pumps (up from 93% for the same period in 2021).
Why the condition of the water matters
The water inside a heating system does not stay perfectly clean. Over time it can carry sludge, magnetite and debris. Sludge and debris in an old system can restrict flow through radiators, pipework and the heat pump’s heat exchanger and filters. With a system designed around steady, lower-temperature flow, that matters.
There is a British Standard that deals specifically with preparing heating water systems, BS 7593, and building regulations guidance points heat pump commissioning towards an MCS standard:
Building Regulations Approved Document L (para 8.7) says heat pump heating and hot water systems should be commissioned to MCS standard MIS 3005.
You can read about both on our standards page. The practical message is simple: before the heat pump is connected, the existing system should be professionally cleaned and flushed. Our system cleaning guide explains what that involves.
What to read next
If you are considering a heat pump for your own home, the step-by-step guide for homeowners walks through the survey, quote, cleaning, installation, commissioning and aftercare, with questions to ask at each stage. Always check the heat pump manufacturer’s installation manual and warranty terms for their water-quality requirements.
Sources
Last reviewed: . Checked against the sources listed on this page; this is not an independent technical or professional review.
Keep reading
Before anything is connected