Why old systems cause problems for heat pumps
Over years of service, a wet heating system collects sludge, black magnetite from corroding steel radiators, scale and debris such as flux and swarf from earlier work. With a boiler this often goes unnoticed. A boiler runs hot water at relatively modest flow rates and has fairly tolerant waterways.
A heat pump is different. It runs at lower water temperatures and needs higher flow rates to move the same heat. It typically has a compact plate heat exchanger and fine strainers that trap debris. Connect it to a dirty system and that debris quickly gathers where it can do most harm: in strainers, filters, the heat exchanger and the narrowest pipes. The result can be low flow errors, cold radiators, short cycling and higher running costs.
Performance and warranty conditions
Heat pump manufacturers commonly set requirements around system water quality, and installation standards expect systems to be cleaned and flushed before a new heat source is connected. Exact terms vary between manufacturers and products, so we cannot tell you what your warranty says. Ask your installer to show you the relevant conditions for the unit they propose, and keep a record of the cleaning carried out.
We are not able to promise that a clean will guarantee any warranty outcome. What we can say is that a properly cleaned and documented system puts you in a stronger position, and avoids the frustration of a new heat pump struggling from its first week.
What a proper pre-install clean involves
A proper clean is more than adding a bottle of cleaner and draining down the next day. In broad terms it should include:
- An assessment of the existing system: pipe sizes including any microbore, radiator condition, valves and signs of corrosion.
- Physically removing sludge, magnetite and debris from radiators and pipework, circuit by circuit.
- Attention to the problem areas: microbore runs, long legs and radiators that are cold at the bottom.
- Clearing out the cleaning water so it is not left in the system.
- Refilling with clean water and correctly dosed inhibitor, with a magnetic filter and air separation fitted as appropriate for the new heat pump.
- A record of what was done, for you and your installer.
When to do it
Ideally the clean happens shortly before the heat pump is connected, once the installer has finalised the design. That way any radiators being replaced or pipework being upsized are planned together, and the new heat pump only ever sees clean water. If your heat pump is already fitted and showing faults, cleaning can still help, but it is usually more disruptive after the event.
Why we recommend PowDer Flush
We recommend PowDer Flush for pre-install cleaning because it is a thorough professional method delivered by engineers with long experience of system flushing, and because it handles microbore systems as a specialism. Microbore is common in UK homes and is often where chemical-only approaches struggle most.
Our professional view is that a powered physical clean gives a more reliable result on heavily contaminated systems than chemical-only flushing. That is our opinion based on experience in the field, not a laboratory claim, and every system is different. Talk to us and we will tell you honestly what your system needs.
Questions to ask your installer
Whoever installs your heat pump, ask them:
- How will the existing system be cleaned before connection, and by whom?
- Is any of my pipework microbore, and is it suitable for the flow the heat pump needs?
- What water quality and cleaning conditions does the manufacturer warranty set?
- Will a magnetic filter and air separation be fitted?
- Will I get a written record of the cleaning and commissioning?
Frequently asked questions
My radiators heat up fine. Do I still need a clean?
Possibly. Radiators can feel warm with a boiler while still holding sludge that will affect a heat pump running at lower temperatures and higher flow.
Is a chemical flush enough?
In our professional view it often is not on older or heavily sludged systems, especially microbore. Chemicals help loosen deposits, but they need to be properly removed.
Can the installer do the clean?
Some do. Ask exactly what method they use and how thorough it is. We recommend PowDer Flush where a specialist clean is needed.
Does cleaning guarantee my warranty?
No one can guarantee that. Warranty terms are set by the manufacturer. A documented clean helps show the system was properly prepared.
Get the system cleaned before installation day
Call PowDer Flush to talk through your system, your pipework and your installation timetable. Straight answers, no pressure.
Related guides
PowDer Flush
Our recommended professional system clean before a heat pump retrofit, with microbore expertise.
Read moreAdvice for homeowners
Suitability, grants, questions for installers and preparing your system.
Read moreLow flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read more