Why do microbore pipes block more easily?
It comes down to space. The inside of an 8mm or 10mm pipe is small, so any deposit takes up a large share of it. A thin layer of sludge that would make little difference in a 22mm pipe can noticeably reduce flow in microbore.
Microbore layouts also create natural traps. Manifolds, tight hand-formed bends, long runs under floors and dips where pipes pass beneath joists all give heavy magnetite a place to settle. Water slows down at these points, debris drops out and, over years, a partial blockage forms. Steel radiators corroding from the inside keep supplying fresh magnetite.
What is microbore sludge and where does it come from?
Sludge is mostly black iron oxide, called magnetite, produced as steel radiators slowly corrode. It is mixed with scale, flux residue from soldered joints and debris left from earlier work. In a sealed system with weak or absent inhibitor the process continues year after year.
In microbore, sludge tends to collect at the bottom of radiators, at manifolds and at low points. If you have ever bled a radiator and seen black water, you have seen it. Our page on sludge and magnetite in heat pump systems covers the chemistry in more detail.
Why are some radiators cold on a microbore system?
Cold radiators on microbore usually follow one of three patterns. A radiator cold at the bottom and warm at the top usually has sludge settled inside. A radiator that is barely warm all over may be on a partly blocked run, or the system may be badly balanced so that water takes the easy route through nearer radiators. A radiator cold at the top is usually holding air.
On microbore the second pattern is particularly common, because a partial blockage in a thin pipe starves the radiator at the end of it. The radiators nearest the manifold or heat source tend to be fine, and those at the end of long runs struggle. See cold radiators and poor heat for the full fault guide.
Why are my microbore pipes noisy?
Rushing, whistling or ticking from microbore can have several causes. High water speed through a narrow or partly blocked pipe can be noisy. Air trapped in the system makes gurgling sounds. Ticking and creaking often comes from pipes expanding and contracting against joists or clips as they heat and cool.
With a heat pump, higher design flow through thin pipes can make velocity noise more likely, which is one reason microbore needs proper assessment. If noise starts suddenly, or comes with pressure changes, call your installer rather than investigating under floors yourself.
What causes poor circulation in a microbore system?
Poor circulation is the umbrella problem behind most of the others. Common causes include:
- Sludge and magnetite partly blocking pipes, manifolds or valves.
- Radiator valves or lockshields closed, seized or badly set.
- Air locks, particularly after draining down or work on the system.
- Kinked or crushed microbore, often where it passes under floors or behind units.
- A circulating pump or design that does not suit the resistance of the pipework.
- Blocked strainers or filters on a heat pump system.
What are the signs of a blocked microbore system?
Signs to look out for include:
- Radiators cold at the bottom or barely warm, particularly at the end of long runs.
- Black or brown water when a radiator is bled.
- Radiator valves that stick or will not turn.
- The house taking much longer to warm up than it used to.
- On a heat pump: low flow errors, short cycling or a magnetic filter that fills quickly.
- Pinhole leaks in radiators, a sign of internal corrosion.
One sign on its own is not proof. Several together, on a system that has not been cleaned for years, point strongly towards sludge.
How are microbore problems fixed?
The fix depends on the cause. Air is dealt with by bleeding and correct pressure. Balancing problems are fixed by an engineer setting lockshields properly. Closed or seized valves are freed or replaced. Damaged pipe sections are repaired.
Where sludge is the cause, the system needs a thorough professional clean that physically removes deposits from radiators, manifolds and microbore runs, followed by correct inhibitor and filtration. We recommend PowDer Flush for this and explain the process in cleaning microbore pipes. Where a run is undersized for a heat pump even when clean, replacement may be needed; see replacing microbore pipework. If you are about to fit a heat pump, read before you install.
What should homeowners avoid doing?
Please do not try to unblock microbore by heating pipes, bending them, cutting into them or using drain unblockers. Do not drain a sealed system yourself or open any part of a heat pump. Bleeding a radiator with a radiator key, following your installer's guidance and checking the pressure afterwards, is as far as most homeowners should go.
Frequently asked questions
How do I know if my microbore pipes are blocked?
Common signs are radiators cold at the bottom or barely warm at the end of long runs, black water when bleeding, sticking valves and, on a heat pump, low flow errors. An engineer can confirm it.
Can microbore sludge be removed?
Yes, in most cases, with a thorough professional clean that physically removes deposits. Heavily damaged or kinked pipe may need replacing instead.
Will a chemical cleaner unblock microbore?
Chemicals help loosen deposits, but in our professional view a chemical-only flush often leaves sludge behind in microbore. That is our experience, not a laboratory finding.
Why is only one microbore radiator cold?
Usually sludge in that radiator, a partly blocked run, a closed or seized valve, or poor balancing. Start with the safe checks in our cold radiators guide.
Are microbore problems worse with a heat pump?
They tend to show up more, because a heat pump depends on higher flow at lower temperatures and has finer strainers that catch debris a boiler would pass.
Microbore system struggling?
Call PowDer Flush about central heating system cleaning for blocked or sludged microbore, before or after a heat pump install. Read cleaning microbore pipes to see what is involved.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreCleaning microbore pipes
Why standard flushing struggles with microbore, how PowDer Flush approaches it and what to expect on the day.
Read moreSludge and magnetite
What magnetite is, where it comes from, black water, cold radiators, low flow errors and how it is removed.
Read moreCan you use microbore with a heat pump?
The honest answer: it depends on heat loss, flow and pipe condition. What a survey should check before you re-pipe.
Read more