Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Heat pump guides

What size heat pump do I need?

The right size of heat pump comes from a room-by-room heat loss calculation, which works out how many kilowatts (kW) of heat your home loses on a cold day. The heat pump should match that figure plus hot water needs. Rules of thumb based on floor area or your old boiler's size are not reliable.

Why a proper heat loss calculation matters, what kW means, and what a good survey should include.

Why does sizing come from a heat loss calculation?

Every home loses heat through its walls, roof, floors, windows and draughts. On a cold day, the heating system has to replace that heat as fast as it escapes to keep rooms comfortable. A heat loss calculation estimates how much heat each room loses at a chosen outdoor design temperature for your area, then adds them up.

The calculation looks at the construction and size of each room, the insulation, the windows, ventilation and the temperature you want each room to reach. The total tells the designer the heat output the heat pump must provide. The room-by-room figures tell them which radiators are big enough at the planned flow temperature and which need upgrading.

Rules of thumb, such as a figure per square metre or simply matching the old boiler, are not reliable. Boilers are often much larger than the home needs, and two homes of the same size can lose heat very differently. A heat pump sized by guesswork is more likely to run poorly.

What does kW mean for a heat pump?

kW, or kilowatt, is a measure of power: how fast heat is delivered. A heat pump's size is usually given as its heat output in kW under stated conditions. A home that loses heat at a certain rate on a cold day needs a heat pump that can deliver at least that rate at that temperature.

Be aware that a heat pump's output changes with the outdoor temperature and the flow temperature. A unit's headline kW figure may be measured under milder conditions than your coldest days. Ask the installer to show the unit's output at your design outdoor temperature and design flow temperature, not just the name on the box. [CHECK: example heat loss range for a typical UK home, with source].

kWh, by contrast, measures energy used over time and is what appears on your bills. Our running costs guide uses kWh.

What happens if a heat pump is too big?

An oversized heat pump costs more to buy and can run less efficiently. The main problem is short cycling: the unit heats the water quickly, reaches its target, switches off, then starts again soon after. Frequent starts waste energy, put extra wear on the compressor and can make the house feel less comfortable.

Short cycling can also be caused or made worse by low flow, small system water volume and control settings. Our short cycling fault guide explains the causes and what is safe to check.

What happens if a heat pump is too small?

An undersized heat pump may cope in mild weather but struggle in cold spells. Rooms may not reach temperature, the system may lean on an electric backup heater, and running costs can rise sharply. Some people respond by turning up the flow temperature, which reduces efficiency further.

If rooms are cold even though the heat pump is running, the cause could be undersizing, undersized radiators, or poor flow through a dirty system. Our cold radiators and poor heat guide helps you tell these apart.

What should a proper heat pump survey include?

A good survey takes time. Expect the installer to visit, measure and ask questions. It should include:

  • Room-by-room measurements and a heat loss calculation, with the results shared with you.
  • The design outdoor temperature and the design flow temperature they have used.
  • A check of every radiator's output at that flow temperature, and a list of any to replace.
  • A check of pipe sizes, including any microbore, and whether they can carry the required flow.
  • An assessment of the existing system's condition: signs of sludge, cold spots, corrosion, past leaks or repeated pressure loss.
  • A plan for cleaning the existing system before connection, and how flow will be checked.
  • Hot water needs, cylinder size and location.
  • Outdoor unit location, clearances, noise and drainage.
  • Electrical supply checks.

Why check the existing system's condition and flow?

Most UK heat pumps are retrofits onto existing radiators and pipework. The sizing calculation assumes water can flow freely through every radiator. If an old system is full of sludge or magnetite, the real flow may be much lower than the design expects, so even a correctly sized heat pump can underperform.

Checking for signs of sludge and planning a thorough clean before connection gives the design a fair chance. Cleaning will not make an undersized system big enough, but it removes a common, avoidable cause of low flow rate problems. Read before you install for what to ask.

For broader context, see how much does a heat pump cost? and what is an air source heat pump? The Energy Saving Trust also offers independent advice on choosing a system.

Frequently asked questions

What size heat pump do I need for a 3-bed house?

It depends on heat loss, not bedroom count. Two 3-bed houses can need very different sizes. A room-by-room heat loss calculation gives the answer.

Can I size a heat pump from my old boiler?

No. Boilers are often much larger than needed. Using the old boiler's output can lead to an oversized heat pump and short cycling.

Is it better to oversize a heat pump slightly?

Not as a rule. A modest margin may be part of a design, but significant oversizing risks short cycling and higher costs. See short cycling.

How long does a heat loss survey take?

It varies with the size of the home, but a proper survey involves measuring every room, so expect a thorough visit rather than a quick look.

Does insulation change the size of heat pump I need?

Yes. Better insulation and draught-proofing reduce heat loss, which can mean a smaller unit and fewer radiator changes.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497