Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Faults by brand

Common Daikin Altherma heat pump problems

If a Daikin Altherma is not providing the heat you expect, first record whether the problem affects room heating, hot water or both. Room-by-room observations and the timing of symptoms can help your installer investigate circulation, controls, design and equipment without assuming sludge is the cause. Refer warranty repairs to the installer or Daikin.

Heat Pump Faults is independent and is not affiliated with, endorsed by or connected to Daikin Altherma.

Independent, general guidance for Altherma owners. This page concentrates on one diagnostic habit that helps with any heat pump: working out whether the complaint is about heating the rooms, heating the water, or both, and then describing what you see at the radiators.

Is the problem with heating, hot water or both?

Many heat pump installations serve both radiators and a hot water cylinder. When something feels wrong, the first useful question is which side is affected. Rooms cold but plenty of hot water suggests a different set of causes from hot water running out while rooms are comfortable. Both affected at once points towards something shared, such as low flow through the heat pump, a fault code or a power or controls problem.

Splitting the complaint this way helps your installer go straight to the relevant settings and components instead of checking everything. It applies to any brand of heat pump, not just Altherma.

What if only the rooms are cold?

When hot water is fine but the house is not warm enough, look at the heating side. Common causes on heat pumps generally include schedules and target temperatures, weather compensation set lower than the house needs, radiators too small for heat pump temperatures, poor balancing, and sludge in radiators or pipework reducing output and flow. See cold radiators and poor heat and do you need bigger radiators for a heat pump?

What if only the hot water is a problem?

If rooms are fine but hot water runs short or is not as hot as you expect, it is usually a controls, scheduling or cylinder question for your installer. Hot water timing and temperature settings are set at commissioning, and changes should follow the installer's advice. We do not describe controller menus or settings here, because they vary by equipment and must come from your documentation.

What room and radiator observations are most useful?

Walk round the house after the heating has been on for a while and note, room by room:

  • Whether the room reached its target temperature, and how long it took.
  • Which radiators feel warm all over, and which do not.
  • Any radiator cold along the bottom, which often points to sludge.
  • Any radiator cold at the top, which often points to air.
  • Radiators far from the heat pump that are cooler than those nearby, which can suggest balancing or flow problems.
  • Thermostatic valves turned down, furniture or curtains blocking radiators.

A simple table of rooms against these notes is one of the most useful things you can hand an engineer.

What about Altherma fault codes?

If a code appears, record it exactly with the date and whether heating or hot water was running. Codes and their meanings depend on the specific equipment, so use the official documentation or ask your installer: [CHECK: error code and meaning from manufacturer manual]. Official product information is on the Daikin UK website.

When should a professional take over?

Call your installer for any code, lockout, leak, pressure loss or unusual noise, and for any problem under warranty: [CHECK: brand warranty wording + source link]. Give them your room-by-room notes and say clearly whether heating, hot water or both are affected. If they find sludge in radiators or the filter, a professional clean addresses the cause. PowDer Flush is a central heating system cleaning service and does not repair heat pumps; see PowDer Flush.

Never open the indoor or outdoor units or touch refrigerant or electrical parts. Bleeding radiators as your installer has shown you, then checking the pressure gauge, is a reasonable homeowner task.

Does the time of day tell me anything?

Often, yes. Note whether rooms cool down at the times hot water is being heated, first thing in the morning after a setback, or only on the coldest evenings. A complaint that lines up with hot water times is a different conversation with your installer from one that appears only in very cold weather. Write the times beside your room notes so the pattern is easy to see. Keep the notes for at least a week, because one day rarely shows the whole picture, and bring them to the visit rather than relying on memory.

Do these checks apply to other brands?

Yes. This page does not suggest Altherma units have any particular fault. Separating heating from hot water and observing radiators carefully are whole-system habits that help with every make. Sludge, poor flow and undersized radiators affect all heat pumps. See sludge and magnetite, cleaning microbore pipes and before you install.

Frequently asked questions

My Altherma heats water but not the house. Why?

Look at the heating side: settings, weather compensation, radiator sizing, balancing and sludge. Your installer can check.

Why are some radiators cold with my heat pump?

Often balancing, a closed valve, sludge or restricted flow. Note which radiators and where they are cold.

What does my Altherma code mean?

Use the documentation for your equipment or ask your installer, which is where the code and its meaning are listed.

Should I change the hot water settings myself?

Only in ways your installer has shown you. Settings are part of the commissioned design.

Can a dirty system cause Altherma heating problems?

Yes, as with any brand. Sludge reduces radiator output and flow.

Radiators sludged or cold at the bottom?

PowDer Flush handles central heating system cleaning, not Daikin Altherma repairs or Daikin support. If your installer has found sludge affecting your radiators, call to talk about cleaning. See cleaning radiators.

Central heating system cleaning by PowDer Flush Call 07418 608497