Why do case studies matter if you're getting a heat pump?
A heat pump retrofit connects new equipment to an existing home, often using radiators and pipework originally chosen for a boiler. The condition and suitability of that existing system need to be assessed, not assumed. Brochures and specification sheets describe what a heat pump can do. They cannot tell you what an engineer will find inside a particular set of radiators and pipes. A properly documented job can help explain what was inspected, which problems were identified and how decisions were made.
For homeowners, a good case study shows what a system like yours can look like, what an engineer checks, and what changed after the work. For installers, it shows the conditions investigated when there are low flow errors or uneven heating, and what was done before connection. The condition of the existing system is one factor in heat pump performance, alongside heat loss, emitter sizing, design temperatures and controls. Identifying restrictions before installation lets the installer plan remedial work rather than discover them after the new equipment is connected.
Case studies are also easy to make look better than they were. That is why we think it is worth knowing what to look for in any case study, on this site or anywhere else:
- Measured readings before and after, such as flow rate and temperature difference, with the units and the conditions under which they were taken.
- An honest statement of anything that was not measured.
- The system type and pipe size, so you can judge whether it resembles your own.
- Photos of the actual job, not stock images.
- A general location and date, without personal details.
- Any customer comment shown only with permission, and never written for them.
If a case study cannot answer most of those, treat its conclusions with care. Ours will follow the same standard, and some entries may say that a reading was not taken rather than fill the gap.
Which case studies have been published?
None yet. This collection is open, but it is empty.
No case studies have been published yet, so there is nothing to filter.
No case studies are published yet
We will only add a case study here once the real job details have been supplied and checked: the property and system, what was found, what was done and what was measured before and after. Until then, this space stays empty rather than showing examples, mock-ups or borrowed results.
In the meantime, the guides on what to do before you install, cleaning microbore pipes and low flow errors explain the problems these case studies will cover.
What will each published case study include?
Every entry will use the same structure: a short summary of the problem, the work and the result; a facts table covering the property, system, pipe size and number of radiators; the symptoms reported; what was found; what was done and how long it took; and a before and after results table with notes on how measurements were taken. Photos and customer comments appear only when they exist and, for comments, only with permission.
For background on the problems these jobs involve, read before you install, cleaning microbore pipes and PowDer Flush.
Other heat pump case studies worth reading
These outside collections are listed for independent reading. Each link is still being verified, so placeholders are shown as plain text until a confirmed official address is added.
- Energy Saving Trust heat pump case studies [CHECK: link to official case studies, e.g. Energy Saving Trust]
- MCS published installation case studies [CHECK: link to official case studies, e.g. MCS]
Have a similar problem?
If you have cold radiators, sludge, microbore pipework or a heat pump on the way, call PowDer Flush about central heating system cleaning. This line is not for heat pump repairs or manufacturer support. Installers can read about pre-install system cleaning for heat pump installers.
Frequently asked questions
Do I need my system cleaned before a heat pump?
On most older systems, a proper clean before connection is worthwhile, because sludge and magnetite that a boiler tolerated can upset a heat pump. Agree the method and timing with your installer. See do you need a power flush before a heat pump?
Can microbore systems be cleaned rather than replaced?
Often they can be cleaned, but whether microbore is suitable for a heat pump is a design question for your installer. Cleaning cannot fix undersized pipework. See cleaning microbore pipes.
How do you measure whether a clean has worked?
Useful checks include water condition, how evenly radiators heat, what collects in the filter, and readings such as flow rate and temperature difference taken in comparable conditions before and after. Any target figures should come from the design or manufacturer documentation: [CHECK: measurement guidance source].
How long does a pre-install clean take?
It depends on the number of radiators, the pipework and how dirty the system is: [CHECK: typical duration range]. Ask for an estimate when you book.
Will a dirty system affect my heat pump warranty?
Manufacturers commonly set expectations for water quality, but the terms vary: [CHECK: brand warranty wording + source link]. Ask your installer and keep records. See heat pump warranties and system cleaning.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read morePowDer Flush
Our recommended professional system clean before a heat pump retrofit, with microbore expertise.
Read moreCleaning microbore pipes
Why standard flushing struggles with microbore, how PowDer Flush approaches it and what to expect on the day.
Read morePre-install system cleaning
Reducing callbacks and low flow complaints, working alongside your programme, and the referral scheme.
Read more