What is the difference between primary and radiator pipework?
The primary pipework carries water between the heat pump and the main parts of the system: the house heating circuit, the hot water cylinder and any buffer or header. It carries the whole flow the heat pump produces, so it usually needs to be the largest pipework in the system.
Radiator pipework, sometimes called distribution or branch pipework, carries a share of that flow to each radiator. Each branch only has to carry what its radiator needs, so it can be smaller. In many homes there is also a middle layer of main runs feeding groups of radiators, which need to be sized for the radiators downstream of them.
Why does heat pump pipe size depend on the heat loss design?
The flow a pipe needs to carry depends on how much heat it is delivering and the temperature difference the system is designed around. The heat comes from the room-by-room heat loss calculation. Once the designer knows the flow, they choose a pipe size that carries it without too much resistance or noise.
That is why the same 15mm pipe can be perfectly adequate in one house and inadequate in another. Pipe size is an output of the design, not a starting assumption. MCS publishes standards that certified installers work to on this subject; check the current documents rather than relying on summaries: [CHECK: MCS wording on pipe sizing + source link].
Is 15mm pipe OK for a heat pump?
It can be suitable for some radiator branches, but diameter alone is not enough to decide. A designer needs to assess the heat being carried, pipe length, fittings, available pressure and pipe condition. Suitability for a main run feeding several radiators or for the primary connection depends on the total flow required: [CHECK: 15mm pipe flow capacity at design pressure drop, from installer design tables with source].
If a 15mm main run is feeding many radiators, the designer may recommend upsizing it. If it is just feeding one radiator, it is usually less of a concern.
Is 22mm pipe big enough for a heat pump?
22mm is common for main runs and is sometimes adequate for the primary connection on smaller heat pumps. Larger units may need bigger primary pipework. The manufacturer's installation manual normally gives guidance on connections and the installer's design confirms the size: [CHECK: primary pipe size for your model from manufacturer manual]. We do not give a kW-to-pipe-size table here, because any such table depends on assumptions that may not match your system.
What about 8mm and 10mm microbore?
Microbore has the least margin of any common pipe size. It can sometimes work on short runs to low-heat-loss rooms, but it must be clean and checked against the design. See can you use microbore with a heat pump? and microbore flow rates explained.
How do blockages make undersized pipework worse?
Sludge and magnetite reduce the internal bore of a pipe. In a pipe that already has plenty of margin, a little build-up may not matter. In a pipe that is only just big enough, or a little too small, it can tip the system into low flow. Deposits also collect at bends, valves and low points, adding local restrictions.
So a design that assumes clean pipes is only valid if the pipes are clean. Cleaning the system before installation turns the design's assumption into reality and gives a true baseline. We recommend PowDer Flush for this; read before you install for the full process.
When does pipework need upsizing for a heat pump?
Upsizing is usually recommended when the design shows a run cannot carry its required flow without too much resistance, when noise is likely from high water speed, or when the primary connection is too small for the unit. Common examples include primary pipework from an old boiler location, long main runs feeding many radiators, and microbore runs to large rooms.
Cleaning cannot fix genuinely undersized pipe. Equally, upsizing primary pipework does not fix sludge in the radiators. Often both are needed. See replacing microbore pipework and low flow rate.
What should you ask your installer about pipe sizes?
Ask which pipe sizes they found, which they intend to keep and which to replace, and what flow each section needs to carry. Ask whether the design assumed clean pipes and how the system will be cleaned. Ask them to show you on a simple plan where any upsizing will go, so you understand the disruption involved.
Frequently asked questions
What size pipe does a heat pump need?
It depends on the heat pump size and your home's heat loss design. Primary pipes are usually larger than radiator pipes. Check the manufacturer manual and installer design: [CHECK: primary pipe size from manufacturer manual].
Is 15mm pipe OK for a heat pump?
Often for individual radiator branches. For main runs or primary connections, it depends on the required flow. Your installer's design should confirm.
Do heat pumps need 28mm pipe?
Some larger installations need larger primary pipework. It depends on the unit and design: [CHECK: model connection and pipe size from manufacturer manual].
Can I keep my existing pipework for a heat pump?
Often some of it, if the design confirms it is big enough and it is cleaned. Undersized sections may need replacing.
Does sludge affect pipe size?
It reduces the effective bore, which matters most in small or marginal pipes. Cleaning restores the original bore.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreMicrobore flow rates explained
Why flow rate matters more for heat pumps, how pipe size and sludge both cut flow, and why a survey matters.
Read moreLow flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read moreOne-pipe systems and heat pumps
What a one-pipe system is, why it is a challenge for a heat pump, and the options to consider.
Read more