Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Heat pump guides

How does a ground source heat pump work?

A ground source heat pump circulates a water and antifreeze mix through pipes buried in the ground, where the temperature stays fairly steady all year. The fluid picks up heat from the soil or rock, and the heat pump indoors raises that heat to a useful temperature for your radiators, underfloor heating and hot water.

How ground loops work, how much space they need, and an honest look at when ground source makes more sense than air source.

How does a ground source heat pump collect heat?

A metre or two below the surface, the ground is warmed by the sun and stays at a fairly steady temperature through the seasons. Deeper down, the temperature is steadier still. A ground source heat pump takes advantage of this by running a sealed loop of plastic pipe through the ground.

A mixture of water and antifreeze, sometimes called brine, is pumped through that loop. As it travels through the ground it warms slightly. Back inside the house, the heat pump unit passes that fluid through a heat exchanger, where its heat is picked up by the refrigerant circuit. From there the process is the same as any heat pump: the refrigerant is compressed to raise its temperature, the heat is passed to your heating water, and the refrigerant expands to begin again. Our guide on how a heat pump works explains that cycle with a diagram.

Unlike an air source system, there is no outdoor fan unit. The main heat pump sits indoors, often in a utility room, garage or plant room, alongside the hot water cylinder.

What is the difference between horizontal trenches and vertical boreholes?

The ground loop can be laid in two main ways. The right one depends on how much land you have, the ground conditions and access for machinery.

Ground loop options compared at a general level
Horizontal trenchesVertical boreholes
How it is laidPipe in long, shallow trenches, either straight or in coilsPipe inserted into one or more deep drilled holes
Land neededA large garden or field areaMuch smaller surface area
GroundworkExcavation across a wide area, then reinstatementSpecialist drilling rig and site access
Ground conditionsSuits soil that can be dug easilyDepends on geology; a survey is usually needed
Relative cost[CHECK: typical trench cost range][CHECK: typical borehole cost range]

In some cases a shared ground loop can serve several properties, such as a terrace or a block of flats, with each home having its own heat pump. This is a specialist design and not something to plan without proper advice.

How much space do you need for a ground source heat pump?

There is no single figure, because the size of the ground loop depends on how much heat the home needs and what the ground is like. A home with a high heat loss needs a longer loop than a well-insulated one. [CHECK: indicative trench length or land area per kW, with source].

For horizontal loops, think in terms of a large lawn or paddock that can be dug up and then left without deep-rooted trees or building over it. For boreholes, you need room for a drilling rig to reach the spot and a clear area around it. Indoors, you need space for the heat pump unit, which is roughly the size of a large fridge, plus a hot water cylinder.

A designer should calculate the loop from your heat loss and a ground assessment. An undersized loop can gradually chill the ground over the winter and reduce performance, so this is not a place to cut corners. Our guide on what size heat pump you need explains the heat loss calculation that drives it.

When does ground source suit a property better than air source?

Ground source and air source heat pumps both work well when they are designed properly. Ground source can be the better fit when:

  • You have plenty of land, or good access for drilling, and the groundwork is practical.
  • There is nowhere suitable for an outdoor fan unit, for example because of noise concerns or space at the front of the property.
  • The home has a high, steady heat demand, such as a large rural property off the gas grid.
  • You are already planning major landscaping or building work, which can reduce the extra disruption.
  • You plan to stay in the property for many years and value steady performance through cold spells.

Air source is usually the simpler, quicker and lower upfront cost option for typical homes with small gardens. Ground source tends to deliver steadier performance because the ground temperature changes less than the air, but you should ask any installer to show their expected seasonal performance for your property rather than relying on general claims.

How do disruption and cost compare with air source?

At a general level, ground source installations involve more disruption and a higher upfront cost than air source, mainly because of the groundwork. Trenching can leave a garden looking like a building site for a while, and drilling needs heavy equipment on site. In return, there is no outdoor fan unit and the system has a steady heat source.

We do not publish prices because they vary widely and change over time. [CHECK: typical installed cost range for ground source vs air source, with source]. Grant support may be available for both types; see who is eligible for a heat pump grant and the official Boiler Upgrade Scheme page on GOV.UK. The Energy Saving Trust guide to ground source heat pumps is a good independent reference. For a broader breakdown, read how much does a heat pump cost?

Does the heating system inside the house still matter?

Yes, just as much as with air source. Most ground source heat pumps in existing homes connect to the radiators and pipework that served the old boiler. Ground source systems also run at lower flow temperatures and rely on good water flow, so sludge, magnetite and debris in old radiators can cause the same problems: low flow rate alarms, cold radiators and wasted energy.

Spending money on a ground loop and then connecting it to a dirty heating system undermines the investment. Cleaning the existing system first does not fix an undersized loop or radiator, but it removes an avoidable cause of poor performance. See before you install for what a proper clean involves.

Frequently asked questions

Is ground source better than air source?

Not automatically. Ground source can give steadier performance but costs more to install and needs land or drilling access. The right choice depends on your property and plans.

How deep are ground source heat pump pipes?

Horizontal loops are laid in shallow trenches; boreholes go much deeper. Exact depths depend on the design and ground conditions, so ask your designer to explain theirs.

Does a ground source heat pump need maintenance?

The buried loop needs little attention, but the heat pump, the antifreeze mix and the heating system should be checked periodically, including filters and water quality.

Can I get a grant for a ground source heat pump?

Ground source systems can be eligible for government support. Amounts and rules change, so check our grants guide and the official GOV.UK page.

Do ground source heat pumps make noise?

There is no outdoor fan, so they are generally quiet outside. The indoor unit makes some compressor and pump noise, a little like a large fridge.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497