How do I find out exactly which Vaillant aroTHERM I have?
The aroTHERM name covers more than one version, and the right manual, the right fault meaning and the right support route all depend on knowing precisely what is on your wall and in your garden. Start with your paperwork rather than the unit itself. The installer's handover pack, the commissioning record, the MCS certificate if you have one and any warranty registration confirmation should all record the model.
If paperwork is missing, the outdoor unit and any indoor equipment normally carry a data label. You can read a label that is visible without removing covers or panels; do not open anything to find one. Photograph the label, the controller and the general installation so you have a record you can send to your installer. Official product and support information is on the Vaillant UK website.
What should I write down when something goes wrong?
Clear notes save time on every call. A vague report such as 'it keeps stopping' gives an engineer little to work with. A dated record of what happened, when and in what weather points them towards the cause much faster.
- The exact text or code on the controller, copied character for character, with a photo.
- Date, time and the outdoor conditions: cold and damp, frosty, mild.
- Whether heating, hot water or both were affected.
- What you noticed in the house: which rooms were cold, whether radiators were cold at the top or bottom.
- The pressure gauge reading compared with the normal reading your installer gave you.
- Anything that changed recently: work on the heating, a radiator replaced, settings altered.
What does a low flow message on an aroTHERM usually point to?
On any heat pump, a low flow message means the unit has detected too little water passing through it and is protecting itself. The cause is very often outside the heat pump: sludge and magnetite from old radiators, a strainer or magnetic filter that has filled, valves left closed, air, or pipework that is too small or partly blocked. That applies to every brand, not just this one.
The meaning of any specific code on your model must come from the manual for that model: [CHECK: error code and meaning from manufacturer manual]. We do not guess codes. For the general causes, read low flow rate and flow errors.
Why might my aroTHERM run but the house still feel cold?
A heat pump can be running perfectly well while rooms stay cool. Controls and schedules may have changed, weather compensation may be set lower than the house needs, some radiators may be too small for heat pump temperatures, or sludge may be blocking the lower part of radiators. Remember that heat pump radiators usually feel warm rather than hot; the test is whether rooms reach their target temperature. See cold radiators and poor heat.
Is it an installer call or a cleaning enquiry?
This is the decision we are most often asked to help with, so here is a simple way to think about it. Call your installer first for any fault code, lockout, unusual noise, leak, pressure problem or anything that might be a fault in the heat pump itself, and always while the unit is under warranty: [CHECK: brand warranty wording + source link].
A cleaning enquiry makes sense once an engineer has found evidence that the heating system is dirty: black water when radiators are bled, sludge in the magnetic filter, a strainer that keeps filling, or radiators cold along the bottom. At that point the heat pump is reacting to the system, and cleaning addresses the source. PowDer Flush is a central heating system cleaning service, not heat pump repair. See PowDer Flush.
What can I safely check myself?
Limit checks to those your user manual or installer permits. Check the controller schedule and mode, look at any accessible pressure display and note radiator valve positions. Keep loose leaves and snow clear without removing covers or touching the unit. Bleed radiators only if your installer has shown you how and the user manual allows it. Never open the indoor or outdoor unit, handle refrigerant or work on electrics; leave those jobs to suitably qualified professionals.
Do these principles apply to other heat pump brands too?
Yes. Nothing on this page suggests aroTHERM units have particular defects. The whole-system principles here, clean water, adequate flow, correctly sized radiators and sensible controls, apply to every make. Most UK heat pumps are retrofits onto old radiators and pipework, and a dirty system can make any heat pump struggle. Read sludge and magnetite, and if you have narrow pipes, cleaning microbore pipes. If you are still planning an installation, start with before you install.
Frequently asked questions
Where do I find the model of my Vaillant aroTHERM?
In your handover and commissioning paperwork first, then on any data label visible without removing covers. Your installer can confirm it.
What does my aroTHERM low flow code mean?
Use the manual for your exact model, which is where the code and its meaning are listed. Low flow on any heat pump is often caused by the heating system.
Should I call Vaillant or my installer first?
Your installer, in most cases. They know the system and are usually the route to manufacturer support.
When is a system clean worth considering?
When an engineer finds sludge, black water, a repeatedly filling filter or radiators cold at the bottom.
Can your phone number help with aroTHERM repairs?
No. It is for central heating system cleaning by PowDer Flush only, not heat pump repairs or manufacturer support.
Has your installer found a dirty system?
PowDer Flush handles central heating system cleaning only. We do not repair Vaillant aroTHERM units or provide manufacturer support. If your installer has found sludge, blocked strainers or restricted pipework, call to discuss cleaning. See before you install.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreFaults by brand
Independent, general fault guidance for Vaillant aroTHERM, Mitsubishi Ecodan, Daikin Altherma, Samsung and LG owners.
Read moreLow flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read moreSludge and magnetite
What magnetite is, where it comes from, black water, cold radiators, low flow errors and how it is removed.
Read more