Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Microbore

Microbore flow rates explained

Flow rate matters more for a heat pump than a boiler because a heat pump moves heat at a lower temperature, so it usually needs more water flowing to deliver the same warmth. 8mm and 10mm microbore pipes limit how much water can pass, and sludge narrows them further. The only reliable way to know if your microbore can carry enough is a heat loss and flow design for your home.

This guide explains the principles behind microbore flow without inventing numbers. Every specific figure is marked for checking against your installer's design or an official source, because flow depends on your home, not a general rule.

What is flow rate in a heating system?

Flow rate is the volume of water moving through the heating system, or through one part of it, over a period of time. It is usually expressed in litres per minute or litres per second. The circulating pump creates the flow; the pipes, valves, radiators, filters and heat exchanger all resist it.

The heat delivered to a radiator depends on how much water passes through it and how much the water cools on the way through. More flow, or a bigger temperature drop, means more heat. That simple relationship is at the heart of why heat pumps and microbore need careful thought.

Why does flow rate matter more for heat pumps than boilers?

A boiler typically sends hotter water round the system and is often designed for a larger temperature drop across the radiators. A heat pump runs most efficiently at low flow temperatures and is usually designed for a smaller temperature drop. To deliver the same heat with cooler water and a smaller drop, it generally needs more water flowing.

Heat pumps also protect themselves. If flow through the unit drops below what it needs, it may reduce output, stop or show a flow error. The thresholds are set by the manufacturer: [CHECK: minimum flow rate for your model from the manufacturer manual]. See low flow rate and flow errors.

Can an 8mm microbore pipe carry enough flow for a heat pump?

8mm is the narrowest common microbore size and has the least margin. On a short run to a small, well-insulated room it may carry enough flow. On a long run, or a run feeding a room with higher heat loss, it is much less likely to. We do not publish capacity figures, because they depend on run length, fittings, pump and acceptable pressure drop: [CHECK: 8mm pipe flow capacity at design pressure drop, from installer design tables with source].

The point to take away is that 8mm leaves very little room for error, so its condition matters enormously. A small amount of sludge can tip a marginal run into a failing one.

What is the flow rate of 10mm microbore?

10mm microbore has a larger bore than 8mm, so it can carry more water for the same resistance, but less than 15mm. Whether it is adequate depends on the heat the room needs and the length of run. Any capacity figure should come from your installer's design method: [CHECK: 10mm pipe flow capacity at design pressure drop, with source].

Do not rely on a figure you find in a forum or a general chart without knowing the assumptions behind it. Pipe material, wall thickness, temperature and the number of bends all change the answer.

How does sludge reduce microbore flow?

Sludge reduces the effective bore of a pipe. Because microbore starts small, even a thin coating takes away a significant share of the space water can pass through, and resistance rises quickly as a pipe narrows. Deposits also collect at bends, manifolds and valves, creating local restrictions.

In practice this means a microbore run that would pass a design check when clean can fail when dirty. It also means a design that assumes clean pipes is only valid if the pipes are actually cleaned. That is why we place so much weight on cleaning microbore pipes properly before a heat pump is connected, using PowDer Flush as our recommended method.

Why does a heat loss and flow survey matter?

A room-by-room heat loss calculation tells the designer how much heat each room needs on a cold day. From that, the designer can work out the flow each radiator needs at the chosen flow temperature and temperature difference, then check each pipe run against it.

Without that calculation, decisions about microbore are guesswork in one direction or the other. With it, you can see which runs pass, which fail and which are marginal. MCS publishes the standards certified installers work to; check the current documents at the MCS standards and tools library: [CHECK: MCS wording on heat loss and pipe sizing + source link].

  • Room-by-room heat loss.
  • Required flow per radiator at design conditions.
  • Pipe size and approximate length for each run.
  • Pressure drop across the system against the heat pump pump's capability: [CHECK: pump curve from manufacturer data].
  • Condition of pipes and radiators.

How can flow be improved on a microbore system?

Options include cleaning to restore the original bore, replacing runs that fail the design, reducing heat loss so less flow is needed, adjusting the system design and balancing so water reaches every radiator, and making sure valves and filters are not adding unnecessary restriction. Your installer should choose the combination that fits your home. Read before you install and replacing microbore pipework for more.

Frequently asked questions

What flow rate does a heat pump need?

It depends on the model and the design. Check the manufacturer's manual and your installer's design: [CHECK: model flow requirement from manufacturer manual].

What is the flow rate of 10mm microbore?

It depends on run length, fittings and allowed pressure drop, so we do not quote a single figure: [CHECK: 10mm capacity from installer design tables with source].

Is 8mm microbore OK for a heat pump?

Only on runs the design confirms can carry the required flow. 8mm has little margin, so it must be clean. See can you use microbore with a heat pump?

Does sludge really affect flow that much?

In narrow pipes, yes. A thin layer takes up a larger share of a small bore, and deposits gather at bends and valves.

Can a bigger pump fix microbore flow?

Not reliably. More pump pressure can cause noise and wear and does not fix sludge or undersizing. That is a design decision for your installer.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497