What is BS 7593?
BS 7593 is a British Standard published by BSI. It is a code of practice for the preparation, commissioning and maintenance of domestic central heating water systems, and the current edition's title also refers to cooling water systems. In general terms it covers how a wet heating system should be cleaned, filled, protected and looked after so that the water inside it stays in good condition.
As a code of practice, it gives recommendations and guidance rather than being a law in itself. It is, however, widely referred to by installers, manufacturers and industry schemes. The official standard is available from BSI Knowledge. Edition and current status: [CHECK: current BS 7593 edition and status + source link].
Why does BS 7593 matter for heat pumps?
Heat pumps depend on clean water more than most boilers do. They usually run with higher flow through compact plate heat exchangers and fine strainers. Sludge, magnetite and scale that a boiler tolerated can quickly restrict flow, cause low flow errors and reduce efficiency.
Because most UK heat pumps are retrofitted onto existing systems, the starting condition of the water is often poor. A recognised code of practice on preparing and maintaining system water gives installers and homeowners a shared reference point for what good practice looks like.
Why does BS 7593 matter for installers?
Installers often work to several layers of requirements at once: manufacturer installation instructions, warranty conditions, building regulations and certification scheme standards such as those published by MCS. Some of these may refer to system cleaning and water treatment, and some may refer to BS 7593. Which documents apply, and exactly how, should be checked against the current versions: [CHECK: MCS wording + source link] and [CHECK: brand warranty wording + source link].
For installers, the practical value is consistency and evidence. A system prepared in line with recognised guidance, and documented, is easier to defend if a fault appears later.
Why should homeowners care about BS 7593?
You do not need to read the standard to benefit from it. What matters is that your installer has a clear plan for cleaning the existing system, filling it with clean water, protecting it with suitable treatment and recording what was done. Ask them how their approach relates to BS 7593 and the manufacturer's instructions.
Keep any cleaning certificate, water test result or commissioning record with your heat pump paperwork. If a water-related fault appears, those records help everyone understand what happened.
How does a pre-install clean fit in with BS 7593?
In general terms, BS 7593 covers the stages of preparing a system: cleaning, flushing, filling and protecting the water. A pre-install clean is the cleaning part of that process for an existing system about to receive a heat pump. Specific steps, test methods and acceptance criteria are set out in the standard itself and should be taken from there: [CHECK: BS 7593 cleaning and flushing requirement + source link].
We recommend PowDer Flush for the cleaning stage. It is a professional method focused on physically removing deposits, with microbore as a specialism. Whatever method is used, the installer remains responsible for commissioning the heat pump and the system to the manufacturer's instructions.
What does BS 7593 say about inhibitor and water testing?
Water treatment and testing are part of the subject area the standard covers. We are not going to summarise its specific recommendations on inhibitor dosing, test frequency or water quality parameters, because doing so risks being inaccurate or out of date: [CHECK: BS 7593 water treatment and testing requirement + source link].
Our general guide what water treatment does a heat pump need? explains the role of inhibitor in plain English. Your heat pump manufacturer's instructions will also set out what they expect for their product.
Is this page a substitute for reading the standard?
No. This page is a plain-English introduction written by heating specialists, not a summary of the standard and not legal or compliance advice. Installers should work from the current official text and their certification scheme documents.
What should you ask your installer about BS 7593?
Simple questions get useful answers:
- How will the existing system be cleaned, and how does that relate to BS 7593?
- What water treatment and filtration will be used, and why?
- Will water quality be tested, and will I see the result?
- What do the manufacturer's instructions say about water quality for this model?
- What written record will I receive?
Read the main before you install guide and heat pump warranties and system cleaning for related advice.
Frequently asked questions
What is BS 7593?
The British Standard code of practice for the preparation, commissioning and maintenance of domestic central heating water systems. Get the official text from BSI.
Does BS 7593 apply to heat pumps?
It covers domestic central heating water systems generally, which includes systems served by heat pumps. Check the current scope with BSI: [CHECK: BS 7593 scope + source link].
Is BS 7593 a legal requirement?
It is a code of practice, not a law in itself, but other documents may refer to it. Check any requirement in your installer's scheme or manufacturer warranty: [CHECK: MCS wording + source link].
Does BS 7593 require a power flush?
We do not paraphrase its cleaning requirements. Read the current standard: [CHECK: BS 7593 cleaning requirement + source link].
Where can I read BS 7593?
It is sold by BSI through BSI Knowledge. Installers may have access through their organisation.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreHeat pump warranties and system cleaning
Why manufacturers care about water quality, what to ask your installer and why records matter.
Read moreWater treatment and inhibitor
What inhibitor does, testing water quality, antifreeze approaches in general terms, and why inhibitor alone is not a clean.
Read morePre-install system cleaning
Reducing callbacks and low flow complaints, working alongside your programme, and the referral scheme.
Read more