Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Fault guide

A general guide to heat pump error codes

Every manufacturer uses its own codes, so we cannot list them all. What we can do is explain how to approach any code calmly, what is safe to check, and when to stop.

Step 1Symptoms

Error codes usually show on the indoor controller, the outdoor unit or a phone app. They may come with:

  • The heating or hot water stopping completely.
  • A warning light or alarm sound.
  • The unit restarting by itself after a period.
  • Reduced output while the code is active.
  • Repeated codes at certain times, such as cold mornings.

Step 2Likely causes

Codes broadly fall into groups. Some relate to water flow and pressure, which are often linked to dirty water, restrictions or air. Some relate to temperature sensors and communication between indoor and outdoor parts. Others relate to the refrigerant circuit, the compressor or electrical supply.

In our experience, a large share of codes on retrofit installs relate to flow and water quality rather than the heat pump itself. That is why so many of our guides lead back to the condition of the existing system.

Sensor and communication codes can sometimes be triggered by simple things such as a loose connection or a brief power interruption, but they can also indicate a component fault. Refrigerant and compressor codes always need a qualified engineer. The point of grouping codes is not to diagnose them yourself, but to understand roughly what kind of problem the heat pump is reporting so you can describe it clearly when you call.

It is also worth knowing that some codes are warnings rather than faults. A heat pump may display a code during defrost, during a high demand for hot water, or when it is limiting output to protect itself. Your manual should distinguish between information messages and genuine faults.

Step 3What a homeowner can safely check

Before calling, these checks are safe and often useful.

  • Write down the exact code, the time and what the house was doing.
  • Look the code up in your user manual to see which group it falls into.
  • Check the system pressure gauge.
  • Check power is on at the normal switches and nothing has tripped at the consumer unit. Do not open electrical enclosures.
  • Check radiator valves are open and the outdoor unit is clear of debris.
  • If the manual says a reset is acceptable, try one reset only.

Step 4When to stop and call a professional

Stop and call if the code returns after one reset, if the manual refers to refrigerant, compressor or electrical faults, if anything smells of burning, if water is leaking near electrics, or if a breaker trips again. Repeated resets can mask a developing fault. Refrigerant work needs an F-Gas qualified engineer and electrical work needs a competent electrician. If the system is under warranty, contact the installer first.

When you call, have the code, your notes and the model number ready. Photographs of the controller display and the pressure gauge are helpful too. A clear description often allows an engineer to arrive with the right parts and knowledge first time.

Step 5How prevention helps

Flow and pressure codes are among the most preventable. A system that is cleaned before installation, with good air separation and correct inhibitor, gives the heat pump far fewer reasons to complain. Read the before you install guide and our low flow guide.

After any repair, ask the engineer whether the water was inspected. A code that keeps coming back can be a sign the underlying water quality issue has not been dealt with.

Frequently asked questions

Can I keep resetting an error code?

One reset, if your manual allows it, is reasonable. If the code returns, stop and call an engineer.

Where can I find what my code means?

Your user manual or the manufacturer support pages. Your installer can also explain it.

Are flow codes serious?

They are the heat pump protecting itself. They are often caused by dirty water or restrictions and should be investigated, not ignored.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Call 07418 608497