Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Microbore

Can you use microbore with a heat pump?

Sometimes, yes. Whether microbore can stay depends on how much heat each room needs, how much water each 8mm or 10mm run must carry, and whether the pipes are clean. A proper heat loss and flow survey should decide it run by run, and where microbore is kept it should be thoroughly cleaned before the heat pump is connected.

You may have been told microbore has to go before a heat pump can be fitted. Sometimes that is right. Often it is a sensible default from an installer who has not had time to assess each run. Here is how to get a straight answer for your home.

Do I need to replace microbore for a heat pump?

Not automatically. A heat pump needs enough water to flow through each radiator to deliver that room's heat at a low flow temperature. Whether a microbore pipe can carry that water depends on the pipe's size and length, how many radiators share it, the heat each room needs and how clean the inside of the pipe is.

A small bedroom with good insulation might need only a modest amount of heat, so a short clean 10mm run could cope. A large, draughty lounge at the far end of a long 8mm run is a very different proposition. The answer is often a mixture: keep some runs, replace others. That is why blanket statements in either direction are unhelpful.

What decides whether microbore will work with a heat pump?

Three things decide it, and a good survey will look at all of them.

  • Heat loss. A room-by-room heat loss calculation tells the installer how much heat each room needs on a cold design day. Lower heat loss means less water needs to flow.
  • Flow rate. From the heat loss and the chosen temperature difference, the designer works out the flow each run must carry, and checks whether the pipe can carry it without excessive resistance: [CHECK: flow and pressure-drop figures from the installer's design, with source].
  • Condition. Sludge and magnetite narrow the bore. A pipe that would be adequate when clean may fail when partly blocked.

Why do installers often recommend re-piping microbore?

There are reasonable reasons. Re-piping removes uncertainty: new pipe has a known size and a clean bore, and the installer can design around it with confidence. It also protects the installer from callbacks if an old run turns out to be partly blocked or damaged in a place nobody can see.

There are also less helpful reasons. Assessing each microbore run takes time, and a quick survey may simply assume the worst. Before you agree to lift every floor in the house, it is fair to ask which runs fail the design and by how much, and whether any of them would pass if they were clean.

When is cleaning microbore first a sensible option?

Cleaning first makes sense where the design shows a run is marginal rather than clearly too small, where radiators show classic sludge symptoms such as cold bottoms, or where re-piping would mean major disruption to finished floors, kitchens or bathrooms. A thorough clean gives the installer a reliable baseline, and the heat pump then starts life on clear pipework.

Cleaning is not a substitute for correct sizing. If a run cannot carry the design flow even when perfectly clean, it needs replacing or the heat demand of the room needs reducing, for example through insulation. We will always tell you if we think cleaning will not solve the problem. Our cleaning microbore pipes guide explains the process.

What should a proper heat pump survey check on a microbore system?

When the installer visits, these are reasonable things to expect or to ask for:

  • A room-by-room heat loss calculation, not a rule-of-thumb estimate.
  • Pipe sizes and approximate run lengths recorded for each radiator, including where microbore starts and ends.
  • The location of any manifolds and how many radiators each one feeds.
  • Radiator outputs checked at the proposed flow temperature.
  • Signs of sludge: cold-bottomed radiators, black water when bleeding, previous blockages or valve problems.
  • A clear statement of which runs will be kept, cleaned or replaced, and why.
  • How the system will be cleaned and protected before connection, and how that will be recorded.

What questions should I ask my installer about microbore?

Ask which specific runs fail the design and what flow they need to carry. Ask whether the calculation assumed clean pipes. Ask what happens to retained microbore during installation: will it be cleaned, by whom and by what method? Ask whether insulation improvements would reduce heat loss enough to keep a marginal run.

If you are told everything must go, ask for the reasoning in writing. A good installer will be happy to explain. If you are told everything can stay without any assessment, be equally cautious.

What is our view, as microbore specialists?

After around twenty years flushing heating systems, our view is that many microbore systems are condemned because they are dirty rather than because they are too small, and that many others genuinely do need replacing. The only way to tell the difference is a proper design combined with an honest look at pipe condition.

We recommend PowDer Flush for cleaning retained microbore before a heat pump is fitted. Read before you install for the wider preparation steps, and should you replace microbore pipework? for the other side of the decision.

Frequently asked questions

Can you use 8mm microbore with a heat pump?

Sometimes, on short runs to rooms with low heat loss, if the design confirms it can carry the required flow and the pipe is clean. 8mm has very little margin, so it needs careful checking. See microbore flow rates explained.

Is 10mm microbore OK for a heat pump?

It can be, depending on the heat each room needs and the run length. Your installer's flow design should confirm it: [CHECK: design flow per run from installer calculation].

Will cleaning microbore avoid re-piping?

Only where the pipe is big enough when clean. Cleaning restores lost bore; it cannot enlarge a pipe that is undersized for the design.

Does MCS ban microbore with heat pumps?

We are not aware of a blanket ban, but we do not reproduce standards here. Check the current MCS documents yourself: [CHECK: MCS wording + source link] via the MCS standards library.

Should I clean before or after the survey?

Usually after the survey and before installation, so the clean fits the agreed design. If radiators are badly sludged, the installer may want it done before final decisions.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497