Low flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read the guideCold radiators and poor heat
Cold spots, rooms that never reach temperature, and heat output lower than expected.
Read the guideShort cycling
A heat pump that switches on and off too often, wasting energy and adding wear.
Read the guidePressure loss and air
Falling pressure, gurgling pipes and air that keeps returning after bleeding.
Read the guideNoise, icing and defrost
Humming, rattles, steam clouds and ice build-up on the outdoor unit, and what is normal.
Read the guideError codes
What to check before calling an engineer, and when to stop and call one.
Read the guideHow to use these guides
Pick the guide that best matches what you are noticing. Many heat pump faults overlap, so you may find that two or three guides describe your situation. A system with low flow, for example, will often show cold radiators and frequent switching on and off as well. Where that happens, start with the guide covering the most specific symptom, usually the one your controller or app is reporting.
Each guide follows the same order: symptoms, likely causes, what a homeowner can safely check, when to call a professional, how prevention helps, then a short set of frequently asked questions. That structure is deliberate. It lets you rule out the simple things quickly and recognise the point where you should stop and call someone qualified.
A note on safety
Heat pumps contain refrigerant under pressure and run on mains electricity. Work on the refrigerant circuit needs an F-Gas qualified engineer, and electrical work needs a competent electrician. Our guides never ask you to open sealed panels, remove covers that need tools, or touch refrigerant pipework. If a check seems to require any of those things, it is not a homeowner check.
Equally, do not ignore persistent warnings. A heat pump that is repeatedly locking out is telling you something, and running it hard in that state can make matters worse. Turn it off using the normal controls if a manufacturer or installer has advised you to do so, and get it looked at.
The common thread: water quality
When you read through these guides you will notice one cause comes up repeatedly: dirty system water. Sludge, magnetite and debris from old radiators and pipework restrict flow, coat heat transfer surfaces and block strainers. Because most UK heat pumps are retrofitted onto existing systems, this is not a niche problem. It is one of the most common reasons a perfectly good heat pump does not perform as expected.
Not every fault is caused by dirt. Design problems such as undersized pipework or emitters, incorrect controls settings, poor siting of the outdoor unit and air in the system all play a part, and each guide covers them. But if you are still at the planning stage, cleaning the system properly before the heat pump goes in removes one of the biggest variables. Read our before you install guide for the detail.
Which guide do I need?
Here is a quick way to choose a starting point.
- Controller shows a flow error, or the unit stops soon after starting: low flow rate.
- Some rooms never get warm or radiators are cold at the bottom: cold radiators and poor heat.
- The compressor starts and stops every few minutes: short cycling.
- The pressure gauge keeps dropping, or you hear gurgling: pressure loss and air.
- Loud humming, rattling, steam or ice on the outdoor unit: noise and defrost.
- A code on the display you do not recognise: error codes.
After you have read a guide
If your checks point to a water quality problem, or you are planning a new installation on an older system, talk to a specialist about cleaning. If the problem is with the heat pump itself, contact your installer first, especially if the system is still within its warranty period, because unauthorised work can complicate a claim. Keep a simple note of what you saw, when, and any codes shown. That record saves time for whoever comes to look at it.
Frequently asked questions
Are heat pumps unreliable?
No. Air source heat pumps are well-proven technology. Most of the faults described here come from the system around the heat pump, such as dirty water, pipework and settings, rather than the unit itself.
Will these guides tell me how to fix my heat pump?
They explain causes and safe checks. Repairs to the heat pump, its refrigerant circuit or its electrics must be carried out by a qualified engineer.
Why do you focus so much on cleaning?
Because dirty water from older systems is one of the most common and most preventable causes of heat pump problems on retrofit installs.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related guides
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreLow flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read moreAdvice for homeowners
Suitability, grants, questions for installers and preparing your system.
Read more