Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Fault guide

What water treatment does a heat pump need?

A heat pump system generally needs clean water, a suitable inhibitor at the right concentration, filtration and, for outdoor units, a manufacturer-approved approach to frost protection. The exact products and levels must come from the heat pump manufacturer and your installer. Inhibitor protects a clean system; it does not clean a dirty one.

Water treatment is one of those topics where vague advice causes real problems. This guide explains the principles in plain English. Product choices and dosing belong with your installer and the manufacturer's instructions.

What does heat pump inhibitor do?

Inhibitor is a chemical treatment added to heating system water to slow corrosion and scale formation. By protecting metal surfaces, it reduces the amount of new magnetite produced by steel radiators and helps keep the system cleaner for longer.

Inhibitors must be compatible with the materials in the system and with the heat pump. Manufacturers may specify or approve particular types: [CHECK: approved inhibitor from manufacturer manual]. Do not add products yourself without your installer's agreement.

Does inhibitor fix a dirty heat pump system?

No. Inhibitor is a protective treatment, not a substitute for removing deposits. Adding it to a system full of sludge does not remove the material already settled in radiators and pipework, and it will not clear a blocked strainer or microbore run. The installer should assess both cleaning and ongoing treatment.

If your system is already dirty, it needs cleaning first. See sludge and magnetite and do you need a power flush before fitting a heat pump?

How is heat pump water quality tested?

Water quality can be checked in several ways, from simple on-site tests to samples sent for laboratory analysis. Typical checks look at appearance, inhibitor level and other indicators of water condition. The appropriate tests, frequency and acceptable values are set out in manufacturer instructions and recognised guidance such as BS 7593: [CHECK: water test parameters and frequency from BS 7593 and manufacturer manual + source link].

Ask your installer or service engineer whether water quality will be tested at commissioning and at each service, and ask to see the results.

What antifreeze protection does a heat pump need?

Outdoor monobloc heat pumps have water passing through a unit that sits outside, so frost protection matters. In general terms, manufacturers and installers use one or more approaches: control functions that run the pump or heat pump to prevent freezing, special valves designed to drain the outdoor section if it gets too cold, or a glycol-based antifreeze mixture in the system water.

Which approach is used, and how, is a design decision that must follow the manufacturer's instructions: [CHECK: frost protection method and any glycol type or concentration from manufacturer manual]. Glycol affects flow and heat transfer and needs testing over time. Do not add antifreeze yourself and do not change frost protection settings.

Does a heat pump need a magnetic filter as well as inhibitor?

Filtration and inhibitor do different jobs. Inhibitor slows the formation of new deposits; a magnetic filter captures particles that are circulating. Most installers fit both on retrofit systems, alongside air separation where appropriate. See magnetic filter and strainer problems for what happens when a filter keeps filling.

What is the right order: clean, fill, treat?

In broad terms, good practice is to clean the existing system, remove the cleaning water, fill with fresh water, add the correct treatment, then commission and record. BS 7593 is the British Standard code of practice for the preparation, commissioning and maintenance of domestic central heating water systems and covers this subject in detail; we do not reproduce its steps. See BS 7593 and heat pumps explained.

We recommend PowDer Flush for the cleaning stage, especially on microbore. Your installer then fills, treats and commissions to the manufacturer's instructions.

Why does frequent topping up harm heat pump water quality?

Every time fresh mains water enters a sealed system, it brings dissolved oxygen and minerals with it. Oxygen drives corrosion of steel radiators, producing new magnetite, and minerals can form scale. Fresh water also dilutes the inhibitor already in the system, so its protection weakens with each top-up.

If you find yourself repressurising the system regularly, there is usually a leak or a fault somewhere, and it should be found rather than managed. Note how often you top up and by how much, and tell your installer. See pressure loss and air for the safe checks.

After any repair that involves draining, ask the engineer to confirm that water treatment has been restored to the level the manufacturer specifies: [CHECK: inhibitor concentration from manufacturer manual].

How do you keep heat pump water in good condition?

Simple habits help:

  • Have the system serviced as the manufacturer and installer recommend.
  • Ask for the filter and water condition to be checked at each service.
  • Report repeated pressure loss, as frequent top-ups bring in fresh oxygen.
  • Avoid unnecessary draining and refilling.
  • Keep records of treatment and test results with your heat pump paperwork.
  • If you have microbore, see microbore and heat pumps for why water quality matters so much.

Read before you install if your heat pump has not been fitted yet.

Frequently asked questions

Does a heat pump need inhibitor?

Heat pump systems generally use inhibitor to protect clean water, but the type and level must follow manufacturer instructions: [CHECK: inhibitor requirement from manufacturer manual].

What water treatment does a heat pump need?

Usually clean water, a compatible inhibitor, filtration and an approved frost protection method. Your installer should specify these for your model.

Can I add inhibitor to my heat pump myself?

Please ask your installer first. The wrong product or dose can cause problems, and some systems contain glycol that must not be diluted.

Do all heat pumps need glycol antifreeze?

No. Some use control functions or special valves instead. The method depends on the manufacturer and design: [CHECK: frost protection method from manufacturer manual].

Will inhibitor clear sludge from my heat pump system?

No. Inhibitor protects clean water. Existing sludge needs a professional clean.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497