Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Installers

Pre-install system cleaning for heat pump installers

A pre-install system clean can address contamination that contributes to restricted circulation and low flow complaints on a heat pump retrofit. PowDer Flush is our recommended method, with microbore as a specialism, but cleaning does not replace heat loss calculations or a suitable flow design. Discuss the scope, timing, records and any referral arrangement before booking.

You design, install and commission the heat pump. We deal with the dirt the old system has been collecting for decades. This page explains how that works in practice, and what it can and cannot do for your callback rate.

How does a pre-install clean reduce heat pump callbacks?

On a retrofit, contamination in existing radiators and pipework can move through the circuit and collect in filters or strainers. If it restricts circulation, the owner may notice low flow warnings, poor heat delivery or repeated interruptions. Clearing a component can restore operation without addressing deposits elsewhere, so a recurring blockage warrants a wider assessment rather than an assumption that the component itself is defective.

Cleaning before connection aims to remove contamination before the new equipment is connected. The result needs checking rather than assuming that every deposit has gone. It will not prevent design, controls or product faults, but documenting the condition afterwards can provide a useful baseline for future diagnosis.

Why are low flow complaints so common on retrofit installs?

Heat pumps typically need more flow than the boilers they replace, through finer strainers and compact plate heat exchangers. Existing systems often have partly sludged radiators, magnetite in the pipework and microbore runs with very little margin. Put those together and low flow is a predictable outcome on an uncleaned system.

Your design may assume clean pipework. A pre-install clean helps make that assumption true. See low flow rate and flow errors and microbore flow rates explained for the homeowner-facing explanation you can share.

How does PowDer Flush work alongside your installation programme?

We fit around you. In general the clean is booked after your survey and design are settled and shortly before your connection date, so any radiators you are replacing or pipework you are upsizing are already known. Dates are agreed with you and the customer.

Agree the cleaning scope before booking, including assessment, deposit removal and how the outcome will be recorded. Ask how concerns such as seized valves, corroded radiators or runs that remain restricted will be reported before connection. Confirm who communicates with the homeowner and how access and responsibilities will be coordinated. The heat pump installer remains responsible for the installation design. Read about the PowDer Flush method.

What about microbore on your installs?

Microbore is our specialism. Where your design retains 8mm or 10mm runs, they need to be clean for your flow calculations to hold. Where you are replacing some runs, the retained radiators and pipework still need cleaning so they do not contaminate new pipe. See cleaning microbore pipes and can you use microbore with a heat pump?

How does a pre-install clean fit with standards and warranties?

BS 7593 is the British Standard code of practice for the preparation, commissioning and maintenance of domestic central heating water systems. MCS standards and manufacturer instructions may also refer to system preparation. We do not reproduce their requirements; check the current documents: [CHECK: MCS wording + source link], [CHECK: BS 7593 requirement + source link] and [CHECK: brand warranty wording + source link]. See BS 7593 and heat pumps explained.

Ask which cleaning and water-condition records will be provided, agree that before the visit and keep the documentation with the commissioning records.

How does the installer referral scheme work?

Installers can refer cleaning jobs to PowDer Flush and receive a referral fee of £150 per completed job. Confirm all other participation terms directly before making a referral. No joining terms, minimum volumes or other conditions are set out on this page.

To discuss the scheme, call 07418 608497. That line is for central heating system cleaning and referral enquiries, not heat pump technical support. More detail is on the main installers page.

How should you explain the clean to customers?

Raise it at survey stage, as part of protecting their investment rather than an extra. A simple explanation works: the heat pump runs cooler with more flow, and its parts are more sensitive to dirt than a boiler. You can point customers to before you install and do you need a power flush before fitting a heat pump?, both written in plain English without sales language.

What do you receive after the clean?

Agree the records to be provided before booking. Ask for the date, scope, findings, areas that received particular attention and concerns that could affect design or commissioning. Keep the agreed record with the installation paperwork. It should help identify what further investigation is needed, rather than being treated as a guarantee that every circulation problem has been resolved. Share the relevant findings with the customer so the distinction between completed cleaning and any remaining design decisions is clear.

What can a pre-install clean not do?

It cannot fix undersized pipework or radiators, controls set-up, or faults in the heat pump. Sometimes re-piping is the right answer, and we will say so. Our comparisons between cleaning methods are professional opinion from around twenty years of system flushing, not laboratory claims.

Frequently asked questions

When should the clean happen relative to installation?

Usually after the design is settled and shortly before connection, so nothing new contaminates the system afterwards. We agree dates with you.

Will you talk to my customer directly?

Only to arrange and carry out the referred clean. The customer relationship stays with you.

What is the referral fee?

£150 per completed PowDer Flush job. Confirm all other participation terms directly before referring.

Does a pre-install clean guarantee no callbacks?

No. It removes a common water-side cause but cannot rule out design, controls or equipment faults.

Can you clean systems with microbore?

Yes. Microbore is a PowDer Flush specialism.

Talk to PowDer Flush about your next install

Call PowDer Flush about central heating system cleaning ahead of your heat pump installs, and to discuss the referral scheme. This line is for cleaning enquiries, not heat pump technical support.

Central heating system cleaning by PowDer Flush Call 07418 608497