What do a heat pump magnetic filter and strainer do?
A magnetic filter is usually fitted on the return pipework before the heat pump. It uses a strong magnet to capture magnetite particles from the water as they circulate, along with some non-magnetic debris. A strainer is a fine mesh, often built into or supplied with the heat pump, that physically stops particles from entering the plate heat exchanger.
Both are protective. They are there to catch dirt so it does not reach the parts of the heat pump that are hardest and most expensive to clean or replace. Exact locations and designs vary by manufacturer and installer: [CHECK: filter and strainer arrangement from manufacturer manual].
Why does my heat pump filter keep blocking?
Because the dirt is still coming from somewhere. A filter catches what is circulating, but it does nothing about the sludge settled in the bottom of radiators, packed into microbore runs or sitting at low points. Every time the system runs, more of that loosens and travels to the filter.
On a new heat pump fitted to an old, uncleaned system, the higher flow can stir up deposits the boiler left undisturbed. The filter then fills quickly, the strainer blocks and the heat pump shows low flow errors. Clearing the filter brings temporary relief, then it happens again.
What are the signs of a blocked heat pump strainer?
Signs include:
- Low flow or flow switch errors on the controller.
- The unit starting, running briefly, then stopping.
- Radiators slow to warm or cooler than usual.
- A noticeable improvement straight after the strainer or filter is cleaned, followed by a decline.
- Black sludge visible when an engineer cleans the filter.
What can homeowners safely check on a heat pump filter?
Some magnetic filters are designed so that a homeowner can see or check them; many are not. Strainers inside or next to the heat pump generally need isolating and opening, which is a job for an engineer. Safe steps are:
- Write down the exact error message and when it appears.
- Note the system pressure on the gauge against what your installer told you is normal.
- Check radiator valves are open.
- Only inspect a filter if your installer has shown you how and it is designed for homeowner access.
- Do not open the heat pump casing, isolate pipework yourself or remove internal strainers.
If the problem keeps returning, call your installer, especially if the system is under warranty.
How often should a heat pump filter be cleaned?
That depends on the system, the filter and the manufacturer's instructions. We do not give a fixed interval: [CHECK: filter cleaning interval from manufacturer manual]. As a rule of thumb from experience, a filter checked at the annual service and found only lightly dirty suggests the system is in reasonable condition. A filter that needs clearing every few weeks suggests the system itself needs attention.
When is a full system clean needed?
Consider a full clean when the filter or strainer keeps filling, when radiators are cold at the bottom, when bled water is black, or when low flow errors keep returning after the filter is cleared. At that point the filter is telling you the system is dirty.
We recommend PowDer Flush for this: a professional clean that aims to physically remove deposits from radiators and pipework, with microbore as a specialism. If you have 8mm or 10mm pipework, see cleaning microbore pipes. If you have not had your heat pump fitted yet, the best time is before installation; see before you install.
What should you ask your installer about repeat filter blockages?
Ask what the engineer found in the filter or strainer and how much. Ask whether water samples were dark, whether radiators show cold bottoms, and whether the system was cleaned before the heat pump was connected and by what method. Ask whether any microbore or long runs could be holding sludge, and whether they would recommend a full clean before clearing the filter again.
Keep a simple log of each visit: the date, the error shown, what was cleaned and how dirty it was. A pattern of repeated blockages is useful evidence when deciding with your installer whether a full system clean is the right next step. See heat pump warranties and system cleaning for why records matter.
Is a magnetic filter a substitute for cleaning?
No. A magnetic filter is valuable protection for a clean system, and it is good practice to fit one. But it is not designed to clean a heavily sludged system on its own. Relying on it to do so means repeated filter cleaning, repeated low flow problems and a heat pump working harder than it should. Clean first, then let the filter protect the result. See sludge and magnetite.
Frequently asked questions
Why does my heat pump filter keep blocking?
Because sludge remains in the radiators and pipework. The filter catches it but does not remove the source. A full system clean usually solves the repeat blockages.
Can I clean my heat pump strainer myself?
Only if your installer has shown you how and the part is designed for homeowner access. Otherwise leave it to an engineer.
Does a magnetic filter remove all sludge?
No. It catches circulating magnetite but does not clear deposits settled in radiators or microbore.
Where is the strainer on a heat pump?
It varies by model. Check the manufacturer manual: [CHECK: strainer location from manufacturer manual].
Will a blocked strainer cause a low flow error?
A blocked filter or strainer can restrict circulation, but it is not the only possible cause of low flow. Ask your installer to check the component, the wider system condition and the exact model's requirements.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreSludge and magnetite
What magnetite is, where it comes from, black water, cold radiators, low flow errors and how it is removed.
Read moreLow flow rate and flow errors
Flow errors, lockouts and weak circulation caused by sludge, blocked filters or restrictive pipework.
Read moreCleaning microbore pipes
Why standard flushing struggles with microbore, how PowDer Flush approaches it and what to expect on the day.
Read more