What are the four steps of the heat pump cycle?
Every heat pump, whether it takes heat from the air or the ground, relies on the same loop. A fluid called a refrigerant is sealed inside a circuit of pipes and heat exchangers. It changes between liquid and gas as it goes round, and those changes are what allow it to pick heat up in one place and drop it off in another.
- 1. Evaporate. Cold, low-pressure liquid refrigerant passes through the outdoor heat exchanger (the evaporator). Because the refrigerant boils at a temperature well below that of the outside air or ground, it absorbs heat and turns into a gas.
- 2. Compress. The electric compressor squeezes that gas. Compressing a gas raises its temperature, so the refrigerant leaves the compressor much hotter than it entered.
- 3. Condense. The hot gas flows through a second heat exchanger (the condenser), where it passes its heat to the water in your heating system. As it gives up heat, it turns back into a liquid.
- 4. Expand. The liquid passes through an expansion valve, which drops its pressure and temperature sharply. It is now cold enough to absorb heat from outside again, and the cycle repeats.
The refrigerant never mixes with your heating water. They meet only across the walls of a heat exchanger, which is why the cleanliness of that water still matters: debris and sludge can coat or block the water side of the heat exchanger and stop heat transferring properly.
Why does a heat pump still work in cold weather?
It surprises many people that a heat pump can heat a house when the outside air is near or below freezing. The reason is that the refrigerant boils at a much lower temperature than the outside air, so there is still a temperature difference for heat to flow across. As far as the refrigerant is concerned, a cold winter day is still warm.
What does change is how hard the heat pump has to work. The colder it is outside, and the hotter the water it is asked to produce, the more the compressor must do. That lowers efficiency on the coldest days. A properly sized system is designed around a cold design temperature for your area so it can still meet the heat demand of the house when it matters most.
Air source units also run defrost cycles in cold, damp weather, because moisture in the air can freeze on the outdoor coil. This is normal and is explained in our noise and defrost fault guide.
What is COP, explained simply?
COP stands for coefficient of performance. It is simply the amount of heat delivered divided by the amount of electricity used at a given moment and under given conditions. If a heat pump delivers several units of heat for every unit of electricity, its COP is that ratio.
COP is not a fixed number. It changes with the outdoor temperature and the flow temperature. SCOP, the seasonal coefficient of performance, is an average across a typical heating season and is more useful when thinking about running costs. Manufacturers publish figures measured under standard test conditions, which are not always the same as your home. [CHECK: typical SCOP range for UK air source installs, with source]. For independent information on real-world performance, see the Energy Saving Trust.
Our running costs guide shows how COP feeds into what you actually pay.
Why does a heat pump run at a lower flow temperature than a boiler?
Flow temperature is the temperature of the water leaving the heat pump on its way to your radiators. The smaller the jump between the outside temperature and the flow temperature, the less work the compressor does and the higher the efficiency. So heat pumps are designed to run at lower flow temperatures than most boilers, for longer periods.
To keep rooms warm with cooler water, the system needs enough radiator surface area and a good, steady flow of water through every circuit. This is why installers may upsize some radiators and why the heat loss calculation matters so much. Our guide on what size heat pump you need covers the survey in more detail.
Why does good water flow through a clean system matter?
Because a heat pump works with a small temperature difference between the flow and return water, it needs to move more water through the system to deliver the same heat. Anything that restricts that flow has a big effect: sludge in radiators, magnetite in pipework, partly blocked valves, or debris collecting in strainers and filters.
When flow drops, the heat pump may raise alarms, short cycle or simply fail to heat some rooms. These are among the most common problems we write about, in our low flow rate and short cycling guides.
Most UK heat pumps are retrofits onto existing radiators and pipework, so the condition of that old system really matters. Cleaning it before installation is a sensible step, though it cannot fix a system that has been designed or sized badly. Read before you install for what a proper pre-install clean involves.
Frequently asked questions
How does a heat pump work in the UK climate?
The same way as anywhere else. UK winters are cold but rarely extreme, and the refrigerant can still absorb heat from outside air or ground. Efficiency falls on the coldest days, so correct sizing is important.
Does a heat pump use a lot of electricity?
It uses electricity to run the compressor, fans and pumps, but most of the heat it delivers comes from outside. How much it uses depends on your home's heat loss and how well the system is set up. See our running costs guide.
What refrigerant does a heat pump use?
Different models use different refrigerants. Your installer can tell you which one your unit uses. Any work on the refrigerant circuit must be done by suitably qualified engineers.
Why are my radiators only warm with a heat pump?
It runs at a lower flow temperature for longer. Warm radiators are normal. If rooms are not reaching temperature, see our cold radiators guide.
Can a heat pump also cool my home?
Some heat pumps can reverse the cycle to provide cooling, mainly air-to-air systems. Most air-to-water systems in UK homes are set up for heating and hot water only.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreWhat is a heat pump?
What a heat pump does, the main types, and how it differs from a gas boiler.
Read moreHeat pump running costs
How efficiency, tariffs, heat loss and setup decide what you pay, with a worked method.
Read moreAir source heat pumps
The outdoor unit, cylinder and radiators, monobloc vs split, and what a retrofit involves.
Read more