What decides how much a heat pump costs to run?
Four things do most of the work in deciding your bills:
- Heat demand. How much heat your home loses over a year, which depends on size, insulation, draughts and how warm you keep it.
- Efficiency (COP and SCOP). How many units of heat the heat pump delivers for each unit of electricity. SCOP is the seasonal average and is the better guide for yearly costs. Our guide on how a heat pump works explains COP simply.
- Electricity price. Your unit rate, standing charge and whether you are on a tariff with cheaper times of day.
- Flow temperature. The lower the water temperature the system needs, the more efficiently the heat pump runs. That depends on radiator size, design and controls.
How much electricity does a heat pump use?
A heat pump's electricity use is roughly your home's yearly heat demand divided by its seasonal efficiency. If two homes have the same heat demand, the one with a better designed and better set up system will use less electricity.
Your heat demand may appear on your Energy Performance Certificate, or your installer's heat loss calculation may provide an estimate. If you currently use gas, your past gas use can give a rough clue, although you need to allow for the efficiency of your old boiler. [CHECK: typical annual heat demand range for UK homes, with source].
Hot water is part of the picture too. Heating a cylinder usually needs a higher temperature than space heating, so efficiency for hot water is often a little lower.
How do I work out heat pump running costs? A worked method
This simple method gives a reasonable estimate. Every figure below is a placeholder for you to replace with your own numbers or current official figures.
| Step | What to do | Example figure |
|---|---|---|
| 1. Heat demand | Take your yearly heat demand for heating and hot water in kWh | [CHECK: annual heat demand kWh] |
| 2. Efficiency | Use the SCOP your installer expects for your design flow temperature | [CHECK: expected SCOP] |
| 3. Electricity used | Divide step 1 by step 2 | [CHECK: result kWh] |
| 4. Unit rate | Find your electricity unit rate, or the current cap rate on Ofgem | [CHECK: current unit rate p/kWh] |
| 5. Energy cost | Multiply step 3 by step 4 | [CHECK: result per year] |
| 6. Standing charge | Add the yearly electricity standing charge if comparing whole bills | [CHECK: current standing charge] |
For current unit rates, see the Ofgem energy price cap page. To compare with your current boiler, do the same calculation using your gas use and gas unit rate, and remember that if you remove gas entirely you also stop paying the gas standing charge. The Energy Saving Trust publishes independent comparisons that are updated over time.
Are there special electricity tariffs for heat pumps?
Some energy suppliers offer tariffs designed for homes with heat pumps, or time-of-use tariffs with cheaper electricity at certain times. These can reduce costs if your system and habits suit them, for example by heating the hot water cylinder during cheaper periods. Tariffs and conditions change often, so compare current offers yourself and check the terms carefully. We do not recommend particular suppliers.
A time-of-use tariff works best when the controls are set up to make use of it. Ask your installer to explain how to schedule hot water and whether running the heating in a particular way would help.
What makes heat pump running costs higher than expected?
Most high-bill complaints come back to design, setup or the condition of the heating system rather than the heat pump itself. Common causes include:
- High flow temperature. If radiators are too small, the system may be set to run hotter, which lowers efficiency.
- Sludge and low flow. Most UK heat pumps are retrofits onto old radiators and pipework. Sludge and magnetite restrict flow, so the heat pump struggles to deliver heat and may run longer or hotter. See low flow rate.
- Short cycling. An oversized unit or poor controls can make the heat pump switch on and off frequently, wasting energy. See short cycling.
- Backup heaters. An immersion heater or electric backup running more than intended can raise bills quickly.
- Controls fighting each other. Room thermostats set too low, timers that switch the heat pump off for long periods, or weather compensation turned off.
- Undersized system. If the unit is too small for the house, it may rely on backup heat in cold weather. See what size heat pump do I need?
How can I keep heat pump running costs down?
Start before installation: insist on a proper heat loss calculation, ask what flow temperature the design assumes, and make sure the existing system is cleaned before the heat pump is connected. Our before you install guide explains why. Cleaning cannot fix a system that is poorly designed, but a clean system with good flow gives a good design the best chance of running efficiently.
After installation, let the heat pump run steadily rather than switching it on and off, keep weather compensation enabled, and ask the installer to check the flow temperature and controls if bills look high. Keep an eye on filters, and if radiators develop cold spots, read our cold radiators guide.
Frequently asked questions
How much electricity does a heat pump use per year?
Roughly your yearly heat demand divided by the heat pump's seasonal efficiency. Use the worked method above with your own figures: [CHECK: typical annual electricity use range].
Is a heat pump cheaper to run than a gas boiler?
It depends on efficiency and the relative prices of gas and electricity, which change. Compare both using current rates from Ofgem.
Should I leave my heat pump on all the time?
Usually a heat pump works best running steadily at a lower temperature rather than being switched on and off. Ask your installer how your controls should be set.
Why is my heat pump using so much electricity?
Common causes include a high flow temperature, low flow from a dirty system, short cycling and backup heaters running. See our fault guides.
Do heat pump tariffs save money?
They can, if your usage and controls suit the tariff. Tariffs change often, so compare current options and check the terms.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreHow much does a heat pump cost?
What drives the installed price, a cost breakdown, grants and the hidden costs people forget.
Read moreIs a heat pump worth it?
An honest view of when a heat pump makes sense, with a pros and cons table.
Read moreHow does a heat pump work?
The refrigerant cycle in four steps, COP explained, and why flow matters.
Read more