Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Fault guide

Heat pump buffer tank and low loss header problems

Buffer tanks and low loss headers separate the heat pump's circuit from the heating circuit and can help with flow and short cycling. Problems include temperature mixing, poor heat delivery and, on dirty systems, sludge settling at the bottom where water slows down. Diagnosis and any work on them is a job for your installer or a heating engineer.

Not every heat pump installation has a buffer tank or low loss header, and opinions differ on when they are needed. If yours has one and something is not right, this guide explains what to look for.

What does a buffer tank or low loss header do?

A buffer tank is a small insulated vessel of heating water. A low loss header is a wider section of pipe or a small vessel. Both are used to hydraulically separate the heat pump's own circuit from the heating circuit, so each can have its own pump and flow rate.

Installers fit them for different reasons: to make sure the heat pump always has enough flow even when radiator valves close, to add system volume for defrost or to reduce short cycling, or to connect to existing systems with several zones. Whether one is needed is a design decision: [CHECK: manufacturer guidance on minimum system volume and separation from manufacturer manual].

What are common buffer tank problems with a heat pump?

Issues we hear about include:

  • Mixing and lower radiator temperatures: if the pumps on each side are not set correctly, water can mix in a way that sends cooler water to the radiators, making the heat pump run hotter to compensate.
  • Short cycling: if the buffer is too small or wrongly piped for its purpose. See short cycling.
  • Heat loss from the tank itself if it is poorly insulated or in an unheated space.
  • Air collecting at high points, causing noise or poor circulation.
  • Sludge settling at the bottom on dirty systems.
  • Sensor placement giving misleading readings to the controls.

What are common low loss header problems with a heat pump?

Low loss headers share many of the same issues: flow imbalance between the primary and secondary pumps, temperature mixing, air and dirt collection. Because a header is a point where water slows down, it is a natural place for heavier particles to drop out. Some headers include a drain or dirt collection point that an engineer can use during servicing.

If the secondary pump is moving much more water than the heat pump, cooler return water can mix into the flow, lowering the temperature reaching the radiators. That can lead to the flow temperature being turned up, with a running cost penalty. See flow temperature too high.

How does sludge collect in a buffer tank or low loss header?

Water slows down as it enters a wider vessel. Magnetite is heavy, so as the water slows, particles settle to the bottom. Over time a layer builds up. On a system that was never cleaned before the heat pump was connected, it can build quickly, fed by sludge from old radiators.

Sludge in a buffer reduces usable volume, can interfere with sensors and can be picked back up and carried into the heat pump circuit. Clearing the vessel without cleaning the system only removes what has collected so far. See sludge and magnetite.

What can homeowners safely check?

Safe steps are limited:

  • Note error codes, noises and when problems occur.
  • Check the system pressure gauge and compare it with the normal reading your installer gave you.
  • Check whether the buffer's insulation jacket is intact, without removing it.
  • Feel radiators for cold bottoms, which suggest sludge in the system.
  • Do not open drain points, vents or vessels, and do not adjust pump settings.

When should you call a professional about a buffer tank?

Call your installer if you have repeated short cycling, unexpected high flow temperatures, noises from the buffer or header area, pressure changes, or if your engineer has found sludge there. They can check pump settings, sensor positions, flow on each side and water condition. If the system is under warranty, contact the installer before anyone else works on it.

Where sludge is found, a thorough system clean addresses the source. We recommend PowDer Flush for central heating system cleaning; on microbore systems see cleaning microbore pipes.

Should a buffer tank or header be checked at servicing?

It is sensible to ask. During a service, an engineer can check pump settings, look for air, check sensor readings against expected temperatures and, where the vessel has a suitable drain or dirt collection point, see whether sludge has gathered. What is checked and how often should follow the manufacturer and installer guidance: [CHECK: service schedule from manufacturer manual].

If sludge is found repeatedly, treat it as evidence that the wider system needs cleaning rather than something to clear and forget. Keep notes of what each service finds.

How can buffer and header problems be prevented?

Good design and setup are the main defence, which sits with your installer. On the water side, cleaning the existing system before the heat pump is connected means the buffer or header starts life without a load of sludge to collect. Filtration and correct treatment then keep it that way. Read before you install and water treatment and inhibitor.

Frequently asked questions

Does every heat pump need a buffer tank?

No. It depends on the design and the manufacturer's guidance: [CHECK: manufacturer guidance on buffer use from manufacturer manual].

Can sludge build up in a buffer tank?

Yes. Water slows in the vessel and heavy magnetite settles at the bottom, especially on uncleaned systems.

Why are my radiators cooler than the heat pump flow temperature?

Mixing in a buffer or header is a possible cause if pump flows are not matched. Ask your installer to check.

Can I drain my buffer tank?

No, please leave that to an engineer. Draining parts of a sealed system can cause air, pressure and warranty problems.

Does a low loss header cause short cycling?

Not by itself, but poor setup or design can contribute. See our short cycling guide.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497