Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Fault guide

Noise, icing and defrost problems

Air source heat pumps make some noise and, in cold damp weather, regularly defrost themselves. Knowing what is normal makes it much easier to spot what is not.

Step 1Symptoms

Normal behaviour includes a steady fan and compressor hum, occasional whooshing as the unit changes mode, and clouds of vapour during defrost in cold weather. Signs that something may be wrong include:

  • Rattling, banging, grinding or scraping from the outdoor unit.
  • Ice that builds up and does not clear after defrost cycles.
  • Thick ice on the base or around the fan.
  • Defrost cycles happening very frequently with poor heat in the house.
  • Loud knocking or rushing noises in indoor pipework.

Step 2Likely causes

Outdoor noises often come from loose panels, debris near the fan, poor mounting or anti-vibration feet that have deteriorated. Ice that does not clear can be caused by blocked condensate drainage, poor siting where water drips onto the unit, restricted airflow from plants or walls, or a fault in the defrost process itself.

Indoor noises are usually about water. Low flow and sludge can make pumps work harder, and air in the pipework causes gurgling and rushing. Frequent defrosting with little heat delivered can also be linked to system flow problems, because the unit needs to recover heat from the system water during defrost.

Siting is a frequent background factor. A unit tucked into a narrow passage, under a dripping gutter or against a wall that reflects sound can be noisier and ice up more easily than the same model in an open position. Neighbours may notice noise more than you do, particularly at night, so it is worth listening from outside at different times.

Step 3What a homeowner can safely check

Keep clear of the fan and never remove covers or touch refrigerant pipes.

If you are concerned about noise affecting neighbours, record when it happens and roughly how long it lasts. A short phone video with sound can help your installer judge whether the noise is normal operation or a mechanical problem.

  • Clear leaves, snow and debris from around the outdoor unit, keeping the recommended clearances.
  • Check the area beneath the unit drains freely and is not holding pooled water that freezes.
  • Never chip at ice or pour hot water on the unit.
  • Note when noises occur, and whether they coincide with start-up, defrost or particular weather.
  • Check indoor radiators for air if you hear gurgling.

Step 4When to call a professional

Call your installer if you hear grinding or banging, if ice persists beyond normal defrost, or if noise has changed noticeably. Fan, compressor, defrost and refrigerant faults need an F-Gas qualified engineer. Indoor rushing and gurgling should be checked by a heating engineer, who may look at flow, air separation and water quality.

Describe the noise as specifically as you can: when it starts, how long it lasts and whether it changes with the weather.

Step 5How prevention helps

Good siting and clearances prevent many outdoor problems, which is a design matter for your installer. Indoors, clean system water and good flow help the unit defrost efficiently and quietly, and reduce the pump strain and air that cause noise. Our before you install guide covers this, and PowDer Flush explains our recommended cleaning method.

When planning an installation, ask your installer how they have chosen the position of the outdoor unit, what clearances the manufacturer requires, and how condensate will drain away in freezing weather. These questions cost nothing and avoid many winter problems.

Frequently asked questions

Is steam from my heat pump normal?

Yes, vapour clouds during defrost in cold, damp weather are normal and should stop after a few minutes.

Should I remove ice from the outdoor unit?

No. Let the defrost cycle work. If ice persists, call your installer rather than chipping or using hot water.

Why do my pipes rush and gurgle?

Usually air or flow problems in the system. A heating engineer can check air separation and water quality.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Call 07418 608497