Step 1Symptoms
Low flow tends to show itself in a few recognisable ways. Some appear on the controller; others you notice around the house.
- A flow, low flow or flow switch error on the display or app.
- The heat pump starts, runs briefly, then stops or locks out.
- Radiators warming slowly or unevenly, especially those furthest from the unit.
- A large gap between flow and return temperatures, if your controller shows them.
- Noisy pump or rushing sounds in pipework.
Step 2Likely causes
The most common cause on retrofit installs is dirt. Sludge and magnetite from old steel radiators collect in strainers, filters, the plate heat exchanger and narrow sections of pipe. A heat pump strainer is fine enough to catch debris that a boiler would have passed straight through, so a system that seemed fine on the old boiler can suddenly block after the changeover.
Pipework design is the second big cause. Heat pumps need more flow than boilers, and pipes that were sized for a boiler may be too small. Microbore pipework, typically 8mm or 10mm, has very little margin, and any build-up inside it has a large effect. Other restrictions include partly closed valves, kinked or crushed pipes, a filter that has never been cleaned, and air locks.
- Sludge, magnetite and scale in the system water.
- A blocked strainer or magnetic filter.
- Undersized or restricted pipework, including microbore.
- Closed or partly closed valves, including radiator lockshields.
- Trapped air reducing effective circulation.
Step 3What a homeowner can safely check
There are some sensible, safe checks before you call anyone. Do not open the heat pump casing or any sealed component.
- Note the exact error code and when it appears.
- Check that radiator valves are open, including any that were turned off in unused rooms.
- Look at the system pressure gauge and note the reading against what your installer told you is normal.
- If your installer has shown you how to check an external magnetic filter and it is designed for homeowner access, follow their instructions only.
- Check whether the problem started after any recent work on the heating system.
Step 4When to call a professional
Call your installer or a qualified heating engineer if a flow error keeps returning, if the unit locks out, or if the pressure is outside the normal range. Strainer and filter cleaning inside the system, pump checks and flow measurement are jobs for an engineer. If the heat pump is under warranty, contact the installer first. Where testing shows dirty water, the engineer may recommend cleaning the system, and for microbore installations it is worth using someone with specific microbore experience.
Step 5How prevention helps
Low flow is the fault most directly prevented by cleaning the system properly before a heat pump is fitted. Removing sludge and magnetite before connection means the new strainer, filter and heat exchanger are not immediately loaded with years of debris. It also gives the installer an honest picture of the pipework, so restrictions can be addressed at design stage rather than discovered after commissioning.
We recommend PowDer Flush for this, with microbore systems a specialism. Our before you install guide explains what a proper clean involves.
Frequently asked questions
Why did my old boiler cope but my heat pump does not?
Boilers run at higher temperatures and lower flow rates, and their components are more tolerant of dirt. Heat pumps rely on higher flow through finer strainers and compact heat exchangers.
Is microbore pipework a problem for heat pumps?
Not automatically, but it leaves little margin. It needs to be clean and correctly assessed for flow. A specialist clean is particularly important on microbore systems.
Can I clean the strainer myself?
Only if your installer has shown you how and the part is designed for homeowner access. Otherwise leave it to an engineer.
Will adding inhibitor fix low flow?
Inhibitor helps protect clean water. It does not remove sludge and magnetite that are already in the system.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related guides
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreCold radiators and poor heat
Cold spots, rooms that never reach temperature, and heat output lower than expected.
Read morePowDer Flush
Our recommended professional system clean before a heat pump retrofit, with microbore expertise.
Read more