Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Power flushing

Why didn't my power flush work?

Radiators can stay cold after a power flush for several reasons: deposits left in microbore or badly blocked radiators, air in the system, valves that are closed or stuck, poor balancing, or a design problem cleaning was never going to fix. A careful investigation, not an assumption, is the way to find out which.

It is frustrating to pay for a clean and see little change. Before deciding what went wrong, it helps to separate the possible causes. Some relate to the cleaning, many do not.

Why are my radiators still cold after a power flush?

There are several possible explanations, and more than one can apply at once:

  • Deposits remain: heavily blocked radiators or narrow pipes may not have been fully cleared.
  • Air: refilling a system can leave air pockets, especially in high radiators or long runs.
  • Valves: thermostatic valve pins can stick, and lockshields may have been left closed or altered.
  • Balancing: after a clean, flow may favour some radiators over others until the system is rebalanced.
  • Pump or controls: a weak pump, wrong pump setting, or controls issue reduces circulation.
  • Design: undersized radiators or pipework, or a layout that never heated evenly.

Each needs a different fix, so the first job is working out which applies.

Could blocked microbore be the cause?

Yes, it is a common one. Microbore pipes, usually 8mm or 10mm, have a small bore and often long runs, so even a modest amount of sludge restricts flow significantly, and deposits there can be hard to clear with a general flush. If the cold radiators are all on microbore, and especially if they are furthest from the boiler or heat pump, that is a strong clue. Microbore cleaning is our specialism; see cleaning microbore pipes and common microbore heating problems.

Could the flush itself have been incomplete?

Sometimes. A flush that was short, or that did not deal with radiators individually, can leave deposits in the most blocked places because the water simply bypassed them. That is not always a sign of poor workmanship; some systems are very heavily sludged, and some radiators cannot be cleared without removal. Ask the engineer what they did, how they judged the result and whether the water ran clear at the end. A fair conversation usually gets further than an accusation.

What can I safely check myself?

Keep to simple checks. Feel where each cold radiator is cold: cold top suggests air, cold bottom suggests sludge, cold all over suggests a valve or flow issue. Make sure thermostatic valves are turned up and see whether the pin under the head moves, without forcing it. Check the boiler or system pressure is in the normal range given by your installer or manual. Bleed radiators only if you have been shown how, and check pressure afterwards. Do not open sealed equipment or do gas, electrical or refrigerant work. See cold radiators and poor heat.

What should a professional investigation include?

A good engineer will look at the whole picture rather than repeat the flush. Expect them to check water condition and the filter, vent air, test valves, check the pump and its setting, rebalance where needed and compare radiator sizes with the rooms they heat. If deposits are found in specific radiators or on microbore runs, targeted cleaning or radiator removal may be needed. If the water is clean, the cause is likely elsewhere.

What should I do next?

Start by contacting the engineer who did the flush, with your notes on which radiators are cold and where. Give them the chance to investigate. If the cause turns out to be design or components, a heating engineer can advise on balancing, valves or radiator changes. If deposits remain, particularly in microbore, a more thorough clean may be needed. For a fair look at different methods, see power flush vs PowDer Flush; our recommended method is PowDer Flush.

Our system cleaning case studies page explains what real before and after evidence should look like, and will list genuine jobs once they are published.

What information should I gather before calling anyone?

A few notes make any investigation faster. Write down the date of the flush and who did it, what you were told about the process, and anything you were given afterwards. List each radiator and whether it is warm all over, cold at the bottom, cold at the top or cold throughout, after the heating has run for a while. Note the pressure reading, any noises, and whether problems are worse in certain rooms or at certain times. If you have photos of the water from before and after, keep them. Sharing this calmly with the engineer gives them the best chance of finding the real cause.

What if a heat pump is involved?

If the flush was done before or after a heat pump installation and you are seeing low flow errors or cold rooms, contact the heat pump installer first, as they are responsible for the design and commissioning. Low flow can come from dirt, but also from strainers, valves, air or sizing. See low flow rate and flow errors and choosing the right cleaning method for a heat pump retrofit.

Frequently asked questions

Why didn't my power flush work?

Possible reasons include deposits left in microbore or blocked radiators, air, stuck valves, poor balancing or a design issue. Investigation is needed to tell which.

Why are radiators still cold after a power flush?

Cold top suggests air, cold bottom suggests remaining sludge, cold all over suggests a valve or flow issue.

Is it the engineer’s fault if the flush did not work?

Not necessarily. Many causes are unrelated to cleaning. Talk to the engineer and ask for an investigation first.

Can microbore stop a power flush working?

Narrow pipes are harder to clear and are a common reason for radiators staying cold. Microbore cleaning is our specialism.

Should I get another flush?

Only if deposits are confirmed as the remaining cause. Otherwise fix air, valves, balancing or design first.

Still cold after a flush?

Call PowDer Flush about central heating system cleaning, especially microbore systems where deposits are hardest to shift. We will ask what was done and whether cleaning is likely to be the answer. Read before you install if a heat pump is planned.

Central heating system cleaning by PowDer Flush Call 07418 608497