Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Faults by brand

Common Mitsubishi Ecodan heat pump problems

An intermittent low flow warning or lack of heat on a Mitsubishi Ecodan needs model-specific diagnosis, not a guessed code meaning. A symptom diary and the handover records can help the installer separate water-side restrictions from controls, design or equipment problems. Contact the installer or Mitsubishi Electric for warranty repairs.

Heat Pump Faults is independent and is not affiliated with, endorsed by or connected to Mitsubishi Ecodan.

This independent guide focuses on a frustrating type of problem common to heat pumps generally: the fault that comes and goes. It explains how to build a useful history and why your handover and service records matter.

Why does a low flow problem come and go?

An intermittent fault is harder to pin down than one that is always there, because an engineer may visit on a day when everything works. On heat pumps generally, low flow that appears and disappears often has a water-side explanation. Debris can move around the system and settle in a strainer, causing a fault, then shift. A filter can gradually fill until it crosses a threshold. Air can collect and clear. Flow demand also changes with weather and with radiator valves opening and closing.

None of this is specific to Ecodan. It is how wet heating systems behave, especially old ones with years of sludge. For the general background, see low flow rate and flow errors.

How do I build a useful symptom history?

Treat it like a diary. Each time something happens, spend two minutes recording it. Over a few weeks, patterns appear that one visit would never reveal.

  • The date, time and what the controller displayed, with a photo.
  • Outdoor conditions at the time.
  • Whether the heating, hot water or both were running.
  • How long the problem lasted and whether it cleared by itself.
  • The pressure gauge reading before and after.
  • Anything that preceded it: a filter clean, a radiator bled, settings changed.

Share the whole diary with your installer, not just the latest event. A run of entries showing faults returning after each filter clean, for example, is strong evidence of a dirty system.

How should I treat Ecodan error codes?

Record them exactly and look them up only in the documentation for your specific equipment, or ask your installer. Different models and controllers can use different codes, so a list from elsewhere may mislead you: [CHECK: error code and meaning from manufacturer manual]. Official information is on the Mitsubishi Electric UK website.

Which handover and service records help most?

Your records turn guesswork into evidence. Look out and keep together: the installer's design and quotation, the commissioning sheet, any water test result, details of the filter and inhibitor fitted, any record of system cleaning before installation, and every service report. Service reports are especially useful if they note what was found in the filter or strainer each time.

If your system was not cleaned before the heat pump went in, or there is no record either way, tell your installer. It may explain why the same fault keeps returning. For why records matter to warranty conversations, see heat pump warranties and system cleaning: [CHECK: brand warranty wording + source link].

What should a professional assessment include?

For a recurring flow problem, it is reasonable to expect an engineer to check the strainer and filter and record how dirty they are, look at water condition, confirm valves are open, look for air, check pressure, and review your history. If sludge is found, they should consider where it is coming from rather than simply clearing it again. Radiators cold at the bottom and black water when bleeding point to the wider system. See magnetic filter and strainer problems.

What can owners safely do between visits?

Keep the diary, check the pressure gauge, keep radiator valves open, keep the outdoor unit clear, and bleed radiators only if your installer has shown you how. Do not open the indoor or outdoor units, do not isolate or remove strainers yourself unless they are designed for homeowner access and you have been shown how, and never touch refrigerant or electrical parts.

What if my handover pack is incomplete?

Ask your installer for copies of anything missing, particularly the commissioning record and any note of how the system was cleaned before connection. Keep them with your diary so the next engineer starts with the full history rather than a blank page.

Is this advice specific to Ecodan?

No. We are not suggesting Ecodan units have any particular weakness. Intermittent low flow, good records and proper assessment are whole-system principles that apply across every brand. Where the root cause is sludge, a thorough clean of radiators and pipework usually does more than repeated filter clearing. We recommend PowDer Flush; for narrow pipes see common microbore heating problems. Planning a new install? Read before you install.

Frequently asked questions

Why does my Ecodan low flow fault keep coming back?

On any heat pump, recurring low flow often means debris is still circulating from the system. Ask your installer to check the filter and water condition.

What does my Ecodan error code mean?

Use the documentation for your exact equipment or ask your installer, which is where the code and its meaning are listed.

What records should I keep for my heat pump?

Design, commissioning sheet, cleaning and water treatment details, water tests, service reports and a symptom diary.

Will cleaning the filter fix intermittent low flow?

It may help briefly. If the filter keeps filling, the source of the sludge is still in the system.

Who handles Ecodan warranty repairs?

Your installer or Mitsubishi Electric. PowDer Flush is a cleaning service and does not repair heat pumps.

Repeat low flow traced to dirty water?

PowDer Flush provides central heating system cleaning, not Ecodan repairs or Mitsubishi Electric support. If your installer has traced intermittent low flow to sludge or blocked filters, call to talk about cleaning. Read filter and strainer problems first.

Central heating system cleaning by PowDer Flush Call 07418 608497