Looking for the Heat Pump Federation? The Heat Pump Federation has merged into Heat Pump Association UK (HPA UK). This website is independent and is not connected to the Heat Pump Federation or HPA UK. Find out more

Before you install

Cleaning your radiators before a heat pump install

If you are keeping existing radiators for a heat pump, they should be cleaned first. Sludge settles in the bottom of radiators, reducing the surface that gives off heat and feeding debris to the heat pump. Radiators are best cleaned as part of a whole-system clean, because cleaning one radiator while the rest of the system stays dirty rarely lasts.

Many heat pump installs keep some or all of the existing radiators. That can be a sensible way to save cost and disruption, but only if those radiators are clean. Here is why radiator sludge matters so much more with a heat pump.

What is radiator sludge and why does it matter for a heat pump?

Most UK radiators are pressed steel. Over the years, water inside them slowly corrodes the steel, producing black iron oxide called magnetite. It is heavy, so it settles in the bottom channels of the radiator, mixing with scale and other debris to form sludge.

With a boiler running hot water, a radiator partly filled with sludge may still feel warm enough. A heat pump runs cooler water, so it needs the whole surface of each radiator to deliver heat. Any area lost to sludge is heat output lost. And loose sludge does not stay put: it travels into pipes, valves, filters and the heat pump's strainer. See sludge and magnetite for more.

What do cold spots on radiators tell you?

Feeling your radiators when the heating has been on for a while tells you a lot:

  • Cold at the bottom, warm at the top: usually sludge settled inside.
  • Cold at the top, warm at the bottom: usually trapped air.
  • Cold in the middle or patchy: often heavy sludge or internal corrosion.
  • Barely warm all over: possibly a blocked feed pipe, closed valve or poor balancing.
  • Warm near the valve end only: often restricted flow through the radiator.

Bleeding radiators that are cold at the top is a reasonable homeowner job if your installer has explained how. Black water when bleeding is a strong sign of sludge. The other patterns need a heating professional.

Can you reuse existing radiators with a heat pump?

Often, yes, at least for some rooms. Whether a radiator can stay depends on whether it can deliver enough heat for its room at the heat pump's design flow temperature. Your installer works that out from a room-by-room heat loss calculation and the radiator's rated output adjusted for lower water temperatures. Some radiators will be big enough; others may need replacing or upsizing. Our guide do you need bigger radiators for a heat pump? explains this.

What the calculation assumes is a clean radiator. A radiator with its bottom third full of sludge will not deliver its rated output, so a radiator that passes on paper can fail in practice if it is not cleaned.

Should you clean or replace old radiators?

Replacing radiators is the right answer when they are undersized for the heat pump design, badly corroded, leaking, or so heavily sludged that cleaning is unlikely to restore them. Cleaning makes sense when the radiators are the right size and in sound condition.

Even where some radiators are replaced, the rest of the system needs cleaning. New radiators connected to dirty pipework and old radiators will quickly receive the same sludge.

How are radiators cleaned as part of a whole-system clean?

A good clean treats the system as a whole rather than one radiator at a time in isolation. In broad terms, the engineer assesses each radiator and the pipework feeding it, then works through radiators and circuits to physically move deposits out of the system, paying particular attention to radiators that are cold at the bottom and those on microbore or long runs.

Taking radiators off the wall to clean them outside is sometimes done for individual badly blocked units, but on its own it leaves the pipework dirty. We recommend PowDer Flush as our whole-system method, with microbore as a specialism. Your engineer will explain the specific approach for your home on the day.

What about radiators on microbore pipework?

Radiators fed by 8mm or 10mm microbore are particularly vulnerable. A sludged radiator on a thin pipe has two restrictions in series. Cleaning the radiator without clearing the microbore feeding it, or the other way round, rarely gives a lasting result. See cleaning microbore pipes.

How do you keep radiators clean after a heat pump is fitted?

After the clean, the installer should fit a suitable magnetic filter, add correctly dosed inhibitor and commission the heat pump. Your installer or service engineer should check filter condition and water quality at servicing. Read what water treatment does a heat pump need? and the main before you install guide.

Avoid draining and refilling the system unnecessarily, because fresh water brings fresh oxygen and can restart corrosion. If you notice radiators cold at the bottom again in later years, mention it at the next service rather than waiting.

Frequently asked questions

Do radiators need cleaning before a heat pump?

If they are being reused, yes. Sludge reduces their heat output and can travel to the heat pump's strainer and heat exchanger.

Why are my radiators cold at the bottom?

Usually sludge has settled inside. It reduces heat output and needs a professional clean to remove it.

Can I clean my radiators myself before a heat pump?

Removing and cleaning radiators involves draining a sealed system and is best left to a professional. Bleeding radiators with a key is a sensible homeowner check.

Do I need new radiators for a heat pump?

Not always. It depends on whether each radiator can heat its room at the design flow temperature. See radiators for heat pumps.

Is it worth cleaning radiators I am about to replace?

Radiators being removed do not need cleaning, but the pipework and retained radiators do, so new radiators are not contaminated straight away.

Talk to PowDer Flush before you fit a heat pump

Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.

Central heating system cleaning by PowDer Flush Call 07418 608497