What this page provides
If you arrived through an older Carbonwatch link, you are now reading an independent Heat Pump Faults information page. We have kept this address available so that the link leads to relevant heating information rather than an unrelated homepage. This is not a live carbon monitoring service, a certification scheme or a record of an earlier organisation’s activities.
Our aim here is to explain the questions behind a carbon comparison. We do not have measurements for your property and cannot calculate its emissions simply from its age, postcode or the type of heating fitted. A useful assessment needs the amount of heat required, the energy used to provide it and a clearly identified emissions factor.
How do heat pumps affect heating emissions?
A heat pump moves heat from outside air or the ground into a building using electricity. A gas or oil boiler burns fuel to supply heat. Those are different energy pathways, so comparing only the units shown on the two energy bills can be misleading. The heat delivered to the rooms and hot water must also be considered.
Electricity generation has associated emissions, and these are not the same at every time or in every year. A statement that an electric heating appliance has no combustion at the house is not the same as saying its operation has no emissions. Broader comparisons may also include equipment manufacture, installation, refrigerant losses and eventual disposal. Always check which boundary an environmental claim uses.
For an accessible explanation of the technology, see what is a heat pump? and the Energy Saving Trust’s heat pump information. Neither a general explanation nor a national average guarantees a particular saving at one address.
What makes a carbon comparison fair?
Compare systems meeting the same heating and hot-water needs. A calculation based on a colder house, fewer heated rooms or a different occupancy pattern is not a like-for-like comparison. Weather, the condition of the building and how much hot water is used can all change energy demand.
Ask which year the emissions factors describe, whether the estimate includes direct emissions only or wider energy supply emissions, and whether a heat pump’s assumed performance is seasonal or measured at a single test condition. The UK Government publishes greenhouse gas conversion factors and accompanying guidance. These are reporting resources, not a personalised forecast of your home’s savings.
- Keep the heating demand and comparison period consistent.
- Identify the existing heating fuel and the proposed electricity supply assumptions.
- Use a realistic seasonal performance assumption rather than a best-case headline.
- Record the source, year and calculation boundary alongside any result.
Why do design and system condition matter?
Heat loss, radiator sizing, controls and water circulation affect how a heat pump runs. Sludge or a blocked strainer can restrict circulation, but not every performance problem is caused by dirty water. An engineer needs to distinguish water-quality issues from an unsuitable design, incorrect settings or an equipment fault.
For a retrofit, assessing and cleaning existing radiators and pipework is part of preparing the complete installation. Read before you install and our guide to low flow rate. Cleaning cannot make undersized pipes larger or replace a proper heat-loss calculation. We recommend PowDer Flush for professional cleaning, but do not present it as a carbon certification or promise a quantified emissions reduction.
What information should you keep?
Keep the installer’s design assumptions, commissioning records, energy bills and any available readings that distinguish heating electricity from other household use. A whole-house electricity bill includes cooking, appliances and other loads; it is not automatically a heat pump consumption figure. Record changes in occupancy or heating habits when comparing periods.
If the system is not keeping rooms comfortable, seek a diagnosis instead of assuming a larger bill proves the technology cannot work. Our running-cost guide explains the calculation method without inventing prices or consumption figures.
Frequently asked questions
Does Carbonwatch measure my home’s carbon emissions?
No. This is an educational page, not a monitoring service or calculator. We do not receive readings from your heating system.
Can every home expect the same carbon saving?
No. The heating being replaced, electricity assumptions, building demand and installed performance all matter. Ask for a documented comparison.
Where can I read more about preparing a retrofit?
Start with homeowner advice and the pre-installation guide.
Talk to PowDer Flush before you fit a heat pump
Planning a heat pump on an older system, or chasing a fault on a recent install? Call PowDer Flush for straightforward advice about cleaning the system first. Read our before you install guide for the full picture.
Related pages
Before You Install
Why an old system should be properly cleaned before a heat pump is connected.
Read moreHeat pump running costs
How efficiency, tariffs, heat loss and setup decide what you pay, with a worked method.
Read moreCampaigns and public information
How to assess heat pump campaigns, policy claims and installation advice. Independent information with official sources, not invented campaigns.
Read more